China Custom Socket Fusion Coupling Manufacturers Suppliers - Factory Direct Wholesale

socket fusion Couplings are moulded from HDPE and fused to PE pressure pipe. The range covered on this page runs dn20 to dn63 in SDR11. Sizes are quoted as dn, the outside diameter of the pipe in millimetres.

Everything below applies to the socket fusion Coupling specifically. The neighbouring pages in this section cover selection, dimensions, installation and the application side separately.

Product range

The socket fusion Coupling family covers couplings and repair couplings.

Each type is moulded to the outside diameter of the pipe it joins, so a fitting and its pipe share one fusion geometry. For the socket fusion Coupling that means the socket depth and the fusion zone are set by the dn size and the wall series together, not by the fitting type.

Size range and wall series

Sizes for the socket fusion Coupling are grouped into bands by the work they do.

Size band	Wall series	Typical use
dn20 - dn63	SDR11	service and house connections

Wall series held are SDR11. A unit moulded for one series will not close correctly on pipe of the other, which is the single most common cause of a rejected joint on this product.

Material and marking

socket fusion Couplings are moulded from HDPE compound with the lot certificate on file. Each unit carries the dn size, the SDR and the material grade on the body; black compound with a co-extruded stripe is the standard supply.

Do not fuse a socket fusion Coupling whose marking cannot be read. If the marking is missing, the unit cannot be matched to a wall series and the joint cannot be qualified.

Applications

socket fusion Couplings are used for potable water distribution, gas distribution, industrial process lines, mining dewatering and irrigation. Where the trench is narrow or the pipe cannot be clamped square, this family is chosen over socket fusion because the joint is made from outside the pipe.

For the socket fusion Coupling the range that matters in every one of those sectors is dn20 to dn63, and the wall series follows from the design pressure of the line rather than from the sector itself.

Ordering information

Quote the type, the dn size, the SDR of the mating pipe and the destination port. For the socket fusion Coupling the size band to state is dn20 to dn63.

Other pages in the socket fusion Coupling section, each covering a different angle of the same product family:

HDPE socket fusion Coupling

HDPE Butt Fusion Coupling
Seamless butt fusion coupling for leak-proof HDPE pipe joints.
DN1600 HDPE Equal Tee – Injection Molded, SDR17 PN10 (But...
One-piece injection molded DN1600 HDPE equal tee in PE100, SDR17 PN10. No internal weld seams, butt fusion ends, factory direct. Request a quote today.
Butt Fusion Elbow
Products Description butt fusion elbow - precise connection component for pipeline system steering HDPE hot-melt 90-degree elbow is made by injection molding with PE100 grade new high-density
Butt Fusion Tee
Products Description butt fusion tee - core connection component for pipeline system's diversion and convergence The hot-melt high-density polyethylene (HDPE) three-way fitting produced by
HDPE Butt Fusion End Cap
Products Description HDPE butt fusion end cap HDPE Pipe End Cap Product Introduction HDPE butt fusion end cap is essential terminal fitting for HDPE pipeline system, manufactured with virgin PE100
Butt Fusion Fittings
Products Description butt fusion fittings Food-grade raw materials, providing greater peace of mind 100% brand-new HDPE raw materials, certified by the national drinking water hygiene safety
Fusion Weld Pipe Fittings
Products Description Butt fusion 45° elbow Butt fusion 90° elbow Butt fusion end cap Butt fusion Flange Butt fusion reducer Butt fusion reducing tee Butt fusion equal tee Butt fusion Y tee
Hdpe Pipe Fusion Sdr 11 Fittings
Product Display Butt fusion 45° Elbow Butt fusion Cross Butt fusion Reducer Butt fusion end cap hdpe pipe fusion sdr 11 fittings are made from HDPE, suitable for pipe diameters of ≥ 20mm. They
Hdpe Products Sdr 11 Fittings Reducer
hdpe products sdr 11 fittings reducer is made by injection molding with high-density polyethylene material. It is used for the transition connection of PE pipes of different diameters.
Poly Pipe Fusion Fittings
Fusion HDPE Pipe Reducer are made of brand-new high-quality HDPE raw materials and feature corrosion resistance, anti-aging, and high strength. By using the hot-melt butt welding process, pipes of
HDPE Butt Fusion Fittings
Butt fusion fittings set: elbows, tees, reducers and flange adapters for HDPE systems.

Reviews

James Geddes

The production and service teams of this company are very efficient, so we have been recommending their products and services to our friends around us.

Kim Baker

No one will not love this company's services and products. They are extremely patient, customer service is very serious, and they gave us a lot of guidance.

Russell Krueger

Your staff are very energetic and take things very seriously and meticulously.

Larry Mathewson

First of all, I really like the style of their company's designers. I didn't care much after the contract was signed, which was very worry-free.

Mac Ratchford

We are very satisfied with the product customization service provided by this company, so we have established a long-term business relationship.

Joseph Lavallee

One of the things we really admire about you is that you never back down from a problem, you just get stronger and stronger.

Butt Fusion Coupling is an electrofusion or butt fusion coupling, published here for dn20 to dn63 in SDR11. The socket or spigot end is machined to the outside diameter of the mating pipe, so pipe and fitting share one fusion geometry and the joint is qualified as a pair rather than as two parts. Quote the dn size, the SDR of the pipe it joins and the destination port when asking for a price. Related pages on this site: Ef Coupler, Electrofusion Coupling and Electrofusion Couplings.

China Socket Fusion Coupling Manufacturers Factory Suppliers