The HDPE socket fusion Equal Tees are used wherever PE pressure pipe is used. The application decides which size band and which joint type are economical for the HDPE socket fusion Equal Tee 90 across the dn40 to dn63 range.
The sizes quoted below are the ones that recur in each sector for the HDPE socket fusion Equal Tee 90; the dimensions page carries the full ladder.
| Size band | Wall series | Typical use |
|---|---|---|
| dn40 - dn50 | SDR11 and SDR17 | service and house connections |
| dn63 - dn50 | SDR11 and SDR17 | service and house connections |
| dn63 | SDR11 and SDR17 | service and house connections |
Water supply and distribution
Potable water lines run the whole HDPE socket fusion Equal Tee 90 ladder. Small bands serve house connections, the middle bands serve distribution mains, and the top of the ladder serves trunk mains between treatment plants.
Gas distribution
Gas lines call for a tight fusion record. Every joint is logged with the machine parameters and the operator, and the log travels with the pipeline. For the HDPE socket fusion Equal Tee 90 that record is the deliverable as much as the unit is.
Industrial and process lines
Chemical plants, cooling water and compressed air lines use the same units, selected on pressure class and on the chemical compatibility of the pipe rather than on size alone. For the HDPE socket fusion Equal Tee 90 the range to state is dn40 to dn63.
Mining, dewatering and irrigation
Mining lines run large diameters under low pressure and are often relocated. Irrigation lines run long single sizes and are ordered in container lots rather than piece by piece. Both sectors draw on the same HDPE socket fusion Equal Tee 90 ladder.
Choosing by application
State the medium, the design pressure and the dn size, and the correct wall series follows from the pipe standard the line was designed to. For the HDPE socket fusion Equal Tee 90 that means quoting dn40 to dn63 with the series.
Related pages
Other pages in the HDPE socket fusion Equal Tee 90 section, each covering a different angle of the same product family:
-
![HDPE Equal Tee Butt Fusion Fittings]()
HDPE Equal Tee Butt Fusion FittingsThe tees are molded from brand-new PE100 resin and certified against the major international standards, so they're safe even for drinking water lines. The joints are made by butt fusion: pipe ends
-
![Butt Fusing Tee 280mm]()
Butt Fusing Tee 280mmButt Fusing Tee 280mm is a made-to-order HDPE branch junction for the non-standard 280mm outside diameter, fabricated to your exact main size, branch size, wall series and angle, with butt-fusion
-
![Hdpe Fittings Tee 500mm]()
Hdpe Fittings Tee 500mmHdpe Fittings Tee 500mm is a large-diameter HDPE branch junction built for heavy transmission mains on a 500mm bore, delivering a full-flow, butt-fused take-off that matches the strength and pressure
-
![HDPE Butt Fusion Tee butt-fusion-reducing-tee]()
HDPE Butt Fusion Tee butt-fusion-reducing-teeHDPE Butt Fusion Tee is made of brand-new high-quality HDPE material, which is corrosion-resistant, impact-resistant, and anti-aging. It has a long service life and excellent hot-melt connection
-
![Butt Fusion Tee butt-fusion-wye-dimensions]()
Butt Fusion Tee butt-fusion-wye-dimensionsA butt fusion wye — also called a 45° lateral tee — brings a branch line off a PE100 main through a gently angled 45° socket rather than a square cut. The shallower branching angle keeps flow smooth
Robert Hollingshead
Virginia Healy
Morris Pina
Clarence Simpson
Harold Kelley
Johnnie Lemons