280mm Butt Fusion Tee (Made to Order)

280mm Butt Fusion Tee (Made to Order)

Butt Fusing Tee 280mm is a made-to-order HDPE branch junction for the non-standard 280mm outside diameter, fabricated to your exact main size, branch size, wall series and angle, with butt-fusion square ends on every outlet for a full-bore, leak-free tap.
Send Inquiry

 

 

Equal Tee Dimension Drawing

 

Butt Fusing Tee 280mm

Butt fusion tee dimensions

Butt Fusion Equal TeePE100 restriction butt-fusion fittings / SDR11 & SDR17 / mm
DIMENSION LEGEND dn = Nominal Diameter | L1 = Run Bore Depth (mm) | L2 = Run Bore Depth - Side (mm) | L3 = Branch Bore Depth (mm) | L = Center-to-End Length (mm)
Equal tee size table
Size (dn) L1 (mm) L2 (mm) L3 (mm) L (mm)
dn40 49 +5/0 50 +5/0 80 ± 5 162 ± 5
dn50 55 +5/0 55 +5/0 92 ± 5 184 ± 5
dn63 63 +5/0 63 +5/0 107 ± 5 213 ± 5
dn75 70 +5/0 70 +5/0 120 ± 5 240 ± 5
dn90 76 +5/0 76 +5/0 140 ± 5 268 ± 5
dn110 82 +5/0 82 +5/0 150 ± 5 300 ± 6
dn125 87 +5/0 87 +5/0 163 ± 5 326 ± 6
dn140 85 +5/0 92 +5/0 175 ± 5 336 ± 6
dn160 98 +5/0 98 +5/0 197 ± 5 396 ± 6
dn180 82 +5/0 92 +5/0 200 ± 5 380 ± 6
dn200 * 112 +5/0 112 +5/0 238 ± 5 475 ± 8
dn200 107 +5/0 112 +5/0 235 ± 5 440 ± 8
dn200 107 +5/0 110 +5/0 226 ± 5 445 ± 8
dn225 120 +5/0 120 +5/0 250 ± 5 500 ± 8
dn250 129 +5/0 129 +5/0 283 ± 5 565 ± 8
dn280 136 +5/0 136 +5/0 304 ± 6 602 ± 8
dn315 150 +5/0 150 +5/0 335 ± 6 670 ± 8
dn355 164 +5/0 164 +5/0 360 ± 6 720 ± 10
dn400 140 +5/0 155 +5/0 380 ± 6 720 ± 10
dn450 185 / 130 +10/0 180 +10/0 445 ± 10 890 / 775 ± 12
dn500 230 / 130 +10/0 230 +10/0 510 ± 10 1025 / 835 ± 12
dn560 230 / 140 +10/0 230 +10/0 545 ± 10 1075 / 905 ± 15
dn630 230 / 140 +10/0 240 +10/0 600 ± 10 1175 / 995 ± 15
dn710 165 +10/0 205 +10/0 615 ± 10 1150 ± 15
dn800 165 +10/0 195 +10/0 660 ± 10 1260 ± 15
dn900 180 +10/0 200 +10/0 710 ± 20 1370 ± 25
dn1000 190 +15/0 230 +15/0 800 ± 20 1500 ± 25
dn1200 220 +15/0 280 +15/0 950 ± 20 1780 ± 25
dn1600 250 +20/0 320 +20/0 1200 ± 20 2220 ± 30
Notes: 1) dn450 and above have two length versions (a / b). 2) dn200 marked * is the one-piece (moulded) version; unmarked dn200 rows are turned-OD versions. 3) L1/L2 tolerance +5/0 for dn40–dn400, +10/0 for dn450–dn900, +15/0 for dn1000–dn1200, +20/0 for dn1600. 4) Dimensions in mm.

 

Why a 280mm Made-to-Order Tee

280mm sits outside the standard nominal series, so a matching stock tee usually does not exist. Supplying the junction as a fabricated item lets a network branch onto a non-standard bore without stepping down to a smaller main or forcing an adapter at the take-off. The line keeps its full dimensions right through the branch poin

Fabricated Main-to-Branch Construction

The tee is built around the HDPE main with a branch outlet fused in place, so the jointing wall is homogeneous PE throughout. With no mechanical clamps or sealing rings exposed, the finished junction carries the same pressure rating as the surrounding 280mm pipeline and welds cleanly on site with a standard butt-fusion machine.

Sizing, Wall & Tolerance Data

Main outside diameter: 280mm (project-specified)

Branch outlet: equal or reduced, any angle on request

Material: PE80 / PE100 HDPE

Wall series: SDR11 / SDR17 by pressure class

Supplied with dimensional drawing + material certificate

 

 

Our Butt Fusing Tee 280mm is moulded and tested in our own factory. Qingfa Industry has produced PE100 fittings for 25 years and today runs over 3,000 product varieties. See our factory and quality control.

Hot Tags: 280mm butt fusion tee, butt fusion tee 280mm, non-standard OD HDPE tee, made to order butt fusion tee, 280mm HDPE tee, 280mm tee dimensions, HDPE End Cap, End Cap HDPE Pipe, End Cap HDPE, PE PiPE End Cap, Electrofusion Test Cap, HDPE PiPE End Cap

Previous:No Information

Send Inquiry