SDR 11 is the wall series that puts PE100 pipe and fittings in the PN 16 pressure class: the wall is the outside diameter divided by 11. This page lists every fitting we mould at SDR 11, family by family, together with the wall thickness that goes with each diameter, so you can check what your line needs against what is actually in the mould.
What SDR 11 means
SDR stands for standard dimension ratio, and it is simply the outside diameter divided by the wall thickness. An SDR 11 pipe of dn110 therefore has a nominal wall of 110 ÷ 11 = 10.0 mm. Two pipes of the same diameter but different SDR are not the same pipe: SDR 11 has a thicker wall and a higher rating than SDR 17, and it weighs more per metre.
The ratio converts to a pressure class through the PE100 material values: a minimum required strength of 10 MPa, a design coefficient of 1.25, so a design stress of 8 MPa, and PN = 2 × 8 ÷ (SDR − 1). SDR 11 works out at PN 16, SDR 17 at PN 10 and SDR 9 at PN 20. That rating holds for water at 20 °C; above that the material derates, roughly 0.93 at 30 °C, 0.87 at 40 °C and 0.80 at 50 °C, so a PN 16 line running warm is no longer a PN 16 line.
| SDR series | SDR 17 | SDR 11 | SDR 9 |
|---|---|---|---|
| Nominal pressure | PN 10 | PN 16 | PN 20 |
| Typical service | Water distribution, gravity and low pressure | General pressure pipe, gas distribution | Higher pressure, industrial lines |
If the question is which SDR to choose in the first place, that is a different decision and we keep it on its own page: SDR 11 vs SDR 17 vs SDR 21 compares the three classes on pressure, bore, mass and ring stiffness. This page starts from the point where SDR 11 has already been decided.
SDR 11 wall thickness by diameter
Nominal wall for every diameter in which we mould SDR 11 fittings, with the number of fitting families available at that diameter. At dn110 the wall is 10.0 mm; at dn315 it is 28.6 mm; at dn630 it is 57.3 mm. The full wall range runs from 1.8 mm at dn20 to 127.3 mm at dn1400.
| OD (mm) | Wall (mm) | Families | OD (mm) | Wall (mm) | Families | OD (mm) | Wall (mm) | Families | OD (mm) | Wall (mm) | Families |
|---|---|---|---|---|---|---|---|---|---|---|---|
| dn20 | 1.8 | 14 | dn110 | 10.0 | 21 | dn280 | 25.5 | 12 | dn710 | 64.5 | 7 |
| dn25 | 2.3 | 20 | dn125 | 11.4 | 17 | dn315 | 28.6 | 18 | dn800 | 72.7 | 7 |
| dn32 | 2.9 | 21 | dn140 | 12.7 | 12 | dn355 | 32.3 | 14 | dn900 | 81.8 | 5 |
| dn40 | 3.6 | 24 | dn160 | 14.5 | 20 | dn400 | 36.4 | 14 | dn1000 | 90.9 | 3 |
| dn50 | 4.5 | 28 | dn180 | 16.4 | 13 | dn450 | 40.9 | 14 | dn1200 | 109.1 | 4 |
| dn63 | 5.7 | 34 | dn200 | 18.2 | 20 | dn500 | 45.5 | 13 | dn1400 | 127.3 | 1 |
| dn75 | 6.8 | 16 | dn225 | 20.5 | 17 | dn560 | 50.9 | 7 | |||
| dn90 | 8.2 | 21 | dn250 | 22.7 | 18 | dn630 | 57.3 | 12 |
Electrofusion fittings at SDR 11
Electrofusion is where SDR 11 is most completely covered: 13 families, 289 size entries, and the coupling range reaches dn1400. Sockets are moulded per series, so the fitting you order is either SDR 11 or it is not, there is no adaptor in between.
| Fitting family | SDR 11 range | Sizes at SDR 11 | Of which |
|---|---|---|---|
| Electrofusion Straight Coupling | dn20–dn1400 | 30 | 30 of 32 |
| Electrofusion 90° Elbow | dn25–dn630 | 22 | 22 of 27 |
| Electrofusion 45° Elbow | dn25–dn630 | 22 | 22 of 26 |
| Electrofusion Reducing Coupling | dn32–dn450 | 45 | all 45 |
| Electrofusion Equal Tee | dn25–dn630 | 22 | 22 of 25 |
| Electrofusion Reducing Tee | dn25–dn630 | 70 | 70 of 79 |
| Electrofusion Flange Adapter | dn50–dn560 | 16 | 16 of 19 |
| Electrofusion End Cap | dn40–dn315 | 11 | all 11 |
| Electrofusion Saddle Bypass (Old Model) | dn63–dn315 | 10 | all 10 |
| Electrofusion Saddle Bypass (New Model) | dn63–dn225 | 16 | all 16 |
| Electrofusion Saddle Clamp (Old Model) | dn63–dn315 | 9 | all 9 |
| Electrofusion Saddle Clamp (New Model) | dn63–dn225 | 9 | all 9 |
| Electrofusion Saddle End Plug | dn63–dn315 | 7 | all 7 |
Full size tables for these families are on the tee, elbow, reducer and flange adaptor pages, each of which prints the SDR column per size.
Butt fusion fittings at SDR 11
Butt fusion bodies are machined and moulded to a series too, and the SDR 11 range runs to dn1200 here. Where a size is not in the SDR 11 mould it is machined from the next larger body, which keeps the dimensions and the rating but adds lead time.
| Fitting family | SDR 11 range | Sizes at SDR 11 | Of which |
|---|---|---|---|
| Butt Fusion Reducer | dn50–dn630 | 78 | all 78 |
| Butt Fusion 90° Elbow | dn20–dn1200 | 28 | 28 of 31 |
| Butt Fusion 45° Elbow | dn50–dn1200 | 24 | 24 of 27 |
| Butt Fusion Equal Tee | dn40–dn800 | 23 | 23 of 27 |
| Butt Fusion Reducing Tee | dn50–dn800 | 94 | 94 of 102 |
| Butt Fusion Lateral Tee (45°) | dn63–dn125 | 5 | 5 of 6 |
| Butt Fusion End Cap | dn20–dn1000 | 28 | 28 of 31 |
| Butt Fusion Flange Adapter | dn40–dn1200 | 26 | 26 of 28 |
Socket fusion fittings at SDR 11
Socket fusion stops at dn63, and below that diameter SDR 11 and SDR 17 use the same socket, so the whole small-diameter range is available at SDR 11 without a special order. That covers couplings, tees, elbows, end caps and the threaded transitions.
| Fitting family | SDR 11 range | Sizes at SDR 11 | Of which |
|---|---|---|---|
| Socket Fusion Coupling | dn20–dn63 | 6 | all 6 |
| Socket Fusion Reducing Coupling | dn25–dn63 | 15 | all 15 |
| Socket Fusion Tee | dn20–dn63 | 6 | all 6 |
| Socket Fusion Reducing Tee | dn25–dn63 | 15 | all 15 |
| Socket Fusion 45° Elbow | dn20–dn63 | 6 | all 6 |
| Socket Fusion 90° Elbow | dn20–dn63 | 6 | all 6 |
| Socket Fusion End Cap | dn20–dn63 | 6 | all 6 |
| Socket Fusion Female Threaded Coupling | dn20–dn63 | 6 | all 6 |
| Socket Fusion Male Threaded Coupling | dn20–dn63 | 6 | all 6 |
| Socket Fusion Female Threaded 90° Elbow | dn20–dn63 | 6 | all 6 |
| Socket Fusion Male Threaded 90° Elbow | dn20–dn63 | 6 | all 6 |
| Socket Fusion Female Threaded Tee | dn20–dn63 | 6 | all 6 |
| Socket Fusion Male Threaded Tee | dn20–dn63 | 6 | all 6 |
How each of these methods is actually made, with the step sequence and the defects to watch, is on how HDPE pipes are joined.
PE100 gas series at SDR 11
Gas distribution is the other place SDR 11 dominates, and those are separate moulds from the water series: 20 families, 434 size entries. The tables use a tick per series rather than an SDR column, so SDR 11 and SDR 17 are read across two adjacent columns.
| Fitting family | SDR 11 range | Sizes at SDR 11 | Of which |
|---|---|---|---|
| Electrofusion Straight Coupling | dn20–dn400 | 20 | all 20 |
| Electrofusion Reducing Coupling | dn32–dn400 | 39 | all 39 |
| Electrofusion Saddle Clamp | dn63–dn400 | 13 | all 13 |
| Electrofusion Saddle End Plug | dn63–dn315 | 7 | all 7 |
| Electrofusion Flange Adaptor | dn110–dn400 | 7 | all 7 |
| Electrofusion Reducing Tee | dn25–dn400 | 56 | all 56 |
| Electrofusion End Cap | dn50–dn315 | 10 | all 10 |
| Electrofusion 90° Elbow | dn25–dn400 | 16 | all 16 |
| Electrofusion 45° Elbow | dn25–dn400 | 16 | all 16 |
| Electrofusion Saddle Bypass | dn63–dn315 | 13 | all 13 |
| Electrofusion Equal Tee | dn25–dn400 | 16 | all 16 |
| Butt Fusion Reducer | dn75–dn400 | 55 | all 55 |
| Butt Fusion 45° Elbow | dn75–dn400 | 12 | all 12 |
| Butt Fusion Reducing Tee | dn75–dn400 | 64 | all 64 |
| Butt Fusion 90° Elbow | dn75–dn400 | 14 | all 14 |
| Butt Fusion Stub End | dn40–dn630 | 18 | all 18 |
| Butt Fusion End Cap | dn20–dn630 | 24 | all 24 |
| Condensate Trap (no return branch) | dn63–dn400 | 11 | all 11 |
| Butt Fusion Cross | dn63–dn90 | 3 | all 3 |
| Butt Fusion Equal Tee | dn50–dn630 | 20 | 20 of 24 |
Sorted the other way, by joint method rather than by pressure class, the same families are on the HDPE pipe fittings range page.
Ordering checklist for SDR 11
- Give SDR, not only PN. PN 16 is what SDR 11 delivers on PE100 water; if the line runs above 20 °C, quote the temperature as well and let us derate.
- Give OD and the fusion method. dn315 butt fusion and dn315 electrofusion are different products with different tables.
- Match the fitting series to the pipe series. Mixing SDR 11 pipe with SDR 17 fittings is the single most common ordering mistake on the line.
- On reducers, state both series. A dn160 × dn110 SDR 11 reducer only makes sense if both runs are SDR 11.
- Flange adaptors carry two numbers. The adaptor is SDR 11 and the steel backing ring is PN 16; they are ordered as a pair.
- Sizes marked * or # in the family tables are machined or still in the mould, so ask for the lead time before the tender closes.
Frequently asked questions
Is SDR 11 the same as PN 16?
For PE100 in water service at 20 °C, yes: SDR 11 gives PN 16. They are not interchangeable as ordering terms though, because PN changes with temperature and material while SDR stays a geometric ratio. Order by SDR and quote PN as the rating the line needs.
Do fittings have to be the same SDR as the pipe?
Yes for electrofusion and socket fusion, where the socket is moulded to the wall of one series, and yes for butt fusion, where the two faces being joined must have the same wall. A mismatched joint looks acceptable and fails under test.
What is the wall thickness of SDR 11 pipe at dn110?
10.0 mm nominal, and 14.5 mm at dn160, 18.2 mm at dn200. The wall is always the outside diameter divided by 11, so any diameter can be calculated in the table above.
How far up in diameter can I get SDR 11 fittings?
The electrofusion coupling reaches dn1400 and butt fusion fittings reach dn1200 in SDR 11. Above that the usual choice is SDR 17, which is why the larger sizes in the family tables carry only 17.
Do you make SDR 11 fittings we cannot see in the tables?
The tables come from our own mould list, so anything marked with an asterisk is machined from a larger body and anything unlisted is not in the standard range. Ask before you assume either way.
- HDPE fittings specifications - the full 65-family dimension index this page is cut from
- HDPE tee dimensions, elbow dimensions, reducer size chart, flange adaptor dimensions
- How HDPE pipes are joined - butt, electrofusion, socket and flanged, and which to use at which diameter
- SDR 11 vs SDR 17 vs SDR 21 - choosing the class for a new line
- HDPE pipe pressure rating and testing
- SDR 11 products: SDR 11 electrofusion elbow, SDR 11 electrofusion end cap, SDR 11 / PN 16 flange, SDR 11 socket fusion tee














