A PE main almost always ends somewhere metal. A transition fitting fuses to the plastic pipe at one end and takes a weld or a thread at the other, and the two decisions that matter are the steel end and the coating. All six families are below, with the carbon steel versus stainless comparison made honestly: we make carbon steel, stainless is to order.
What a steel-to-PE transition actually is
A transition fitting is two products joined into one: a PE end that fuses to the plastic pipe, and a steel end that takes a thread or a weld. It exists because a PE main almost always ends somewhere metal: a riser, a valve, a meter, a pump, a steel main in the next street.
We mould the PE end and fit the steel end, and the two variables you choose are the steel end (plain for welding, or threaded) and the coating (standard or 3PE). Length is fixed by the family: the bent versions come in two steel lengths, 1.1 m (a 0.3 m and a 0.8 m section) and 1.5 m (0.3 m and 1.2 m).
| Type | Steel end | Shape | Steel length | PE series | Size range |
|---|---|---|---|---|---|
| Straight | Plain (for welding) | Straight | Standard | SDR 11 | dn25 – dn355 |
| Straight | Plain (for welding) | Straight | Standard | SDR 17 | dn90 – dn355 |
| Bent | Plain (for welding) | 90° bend | 1.1 m (0.3 + 0.8) | SDR 11 | dn25 – dn63 |
| Bent, threaded | Threaded | 90° bend | 1.1 m (0.3 + 0.8) | SDR 11 | dn25 – dn63 |
| Bent | Plain (for welding) | 90° bend | 1.5 m (0.3 + 1.2) | SDR 11 | dn25 – dn63 |
| Bent, threaded | Threaded | 90° bend | 1.5 m (0.3 + 1.2) | SDR 11 | dn25 – dn63 |
Carbon steel or stainless: the decision
Carbon steel is the standard, and it is what all six families above are made in. Stainless is the answer to a specific problem, not a general upgrade, and it is worth being clear about which problem you have before you specify it.
| Carbon steel | Stainless steel | |
|---|---|---|
| Availability in our range | All six families, both coatings, ex works | Made to order, quoted per project |
| Corrosion resistance | Needs the coating to do the work; a damaged coating is the usual failure | Resists chlorides and aggressive soils without relying on a coating |
| Typical reason to choose it | The default for buried mains, risers and meter connections | Aggressive ground, coastal or saline environments, chemical or industrial water, exposed locations where coating repair will not happen |
| Joining the steel end | Weld or thread, the same as any carbon steel pipe | Weld or thread, but the welding procedure is different and dissimilar joints need the right consumable |
| Cost | Lower, and the coating options are already in the price | Higher, and lead time is longer because it is not a stock item |
| Watch out for | Coating damage in handling, and the cut end left bare on site | Threading stainless is slower and galling has to be managed |
Where the environment is aggressive but the budget will not take stainless, the usual compromise is a 3PE coating on a carbon steel end, with the coating extended over the weld zone after installation. That works if someone actually does the coating repair; it does not work if the joint is buried and forgotten.
Choosing the length: 1.1 m or 1.5 m
The bent families come in two steel lengths, and the difference is where the bend sits relative to the surface.
- 1.1 m (0.3 + 0.8) – the shorter steel end. Less steel to bury, less to protect, and the bend is closer to the termination.
- 1.5 m (0.3 + 1.2) – the longer steel end. Used where the transition has to reach further, for example where the PE has to stay below a deeper cover or where the riser has to clear an obstruction.
Both are SDR 11 and both run dn25 – dn63, with plain or threaded steel ends, so length is the only variable between them. The straight families are not split this way: they are supplied in one steel length per size.
Straight transitions
For a PE main that runs straight into a steel main, a valve or a chamber. Plain steel end, so the joint on the steel side is a weld. Two series: SDR 11 from dn25, SDR 17 from dn90.
Straight Steel-to-PE Transition, Plain Steel End, SDR 11dn25–dn355 · 36 sizes
36 combinations, dn25 to dn355, in standard coating and 3PE. Each size is listed against the steel DN it takes.
| Size | Standard Coating | 3PE Coating | Size | Standard Coating | 3PE Coating |
|---|---|---|---|---|---|
| dn25 / DN22 | ✓ | ✓ | dn75 / DN76 | ✓ | ✓ |
| dn25 / DN27 | ✓ | ✓ | dn90 / DN76 | ✓ | ✓ |
| dn32 / DN22 | ✓ | ✓ | dn90 / DN89 | ✓ | ✓ |
| dn32 / DN27 | ✓ | ✓ | dn110 / DN89 | ✓ | ✓ |
| dn32 / DN34 | ✓ | ✓ | dn110 / DN108 | ✓ | ✓ |
| dn40 / DN27 | ✓ | ✓ | dn110 / DN114 | ✓ | ✓ |
| dn40 / DN34 | ✓ | ✓ | dn125 / DN133 | ✓ | ✓ |
| dn40 / DN38 | ✓ | ✓ | dn160 / DN159 | ✓ | ✓ |
| dn40 / DN42 | ✓ | ✓ | dn160 / DN168 | ✓ | ✓ |
| dn40 / DN48 | ✓ | ✓ | dn200 / DN219 | ✓ | ✓ |
| dn50 / DN42 | ✓ | ✓ | dn225 / DN219 | ✓ | ✓ |
| dn50 / DN48 | ✓ | ✓ | dn250 / DN219 | ✓ | ✓ |
| dn63 / DN34 | ✓ | ✓ | dn250 / DN273 | ✓ | ✓ |
| dn63 / DN38 | ✓ | ✓ | dn315 / DN273 | ✓ | ✓ |
| dn63 / DN42 | ✓ | ✓ | dn315 / DN299 | ✓ | ✓ |
| dn63 / DN48 | ✓ | ✓ | dn315 / DN325 | ✓ | ✓ |
| dn63 / DN57 | ✓ | ✓ | dn355 / DN325 | ✓ | ✓ |
| dn63 / DN60 | ✓ | ✓ | dn355 / DN377 | ✓ | ✓ |
Straight Steel-to-PE Transition, Plain Steel End, SDR 17dn90–dn355 · 17 sizes
17 combinations, dn90 to dn355. The higher-series straight transition, for SDR 17 mains.
| Size | Standard Coating | 3PE Coating | Size | Standard Coating | 3PE Coating |
|---|---|---|---|---|---|
| dn90 / DN76 | ✓ | ✓ | dn225 / DN219 | ✓ | ✓ |
| dn90 / DN89 | ✓ | ✓ | dn250 / DN219 | ✓ | ✓ |
| dn110 / DN89 | ✓ | ✓ | dn250 / DN273 | ✓ | ✓ |
| dn110 / DN108 | ✓ | ✓ | dn315 / DN273 | ✓ | ✓ |
| dn110 / DN114 | ✓ | ✓ | dn315 / DN299 | ✓ | ✓ |
| dn125 / DN133 | ✓ | ✓ | dn315 / DN325 | ✓ | ✓ |
| dn160 / DN159 | ✓ | ✓ | dn355 / DN325 | ✓ | ✓ |
| dn160 / DN168 | ✓ | ✓ | dn355 / DN377 | ✓ | ✓ |
| dn200 / DN219 | ✓ | ✓ |
Bent transitions, 1.1 m steel end
The bent transition turns the line up out of the ground, from the PE main into a steel riser. Steel length 1.1 m, made of a 0.3 m and a 0.8 m section. Plain end for welding, or threaded for a screwed connection.
Bent Steel-to-PE Transition, Plain Steel End, 1.1 mdn25–dn63 · 16 sizes
16 combinations, dn25 to dn63. Read the first number as the PE size and the second as the steel size.
| Size | Standard Coating | 3PE Coating | Size | Standard Coating | 3PE Coating |
|---|---|---|---|---|---|
| dn25 × 22 | ✓ | ✓ | dn50 × 42 | ✓ | ✓ |
| dn25 × 27 | ✓ | ✓ | dn50 × 48 | ✓ | ✓ |
| dn32 × 22 | ✓ | ✓ | dn63 × 34 | ✓ | ✓ |
| dn32 × 27 | ✓ | ✓ | dn63 × 38 | ✓ | ✓ |
| dn32 × 34 | ✓ | ✓ | dn63 × 42 | ✓ | ✓ |
| dn40 × 34 | ✓ | ✓ | dn63 × 48 | ✓ | ✓ |
| dn40 × 42 | ✓ | ✓ | dn63 × 57 | ✓ | ✓ |
| dn40 × 48 | ✓ | ✓ | dn63 × 60 | ✓ | ✓ |
Bent Threaded Steel-to-PE Transition, 1.1 mdn25–dn63 · 14 sizes
14 combinations, dn25 to dn63. Threaded steel end; state the thread standard with the order.
| Size | Standard Coating | 3PE Coating |
|---|---|---|
| dn25 × 22 | ✓ | ✓ |
| dn25 × 27 | ✓ | ✓ |
| dn32 × 22 | ✓ | ✓ |
| dn32 × 27 | ✓ | ✓ |
| dn32 × 34 | ✓ | ✓ |
| dn40 × 34 | ✓ | ✓ |
| dn40 × 42 | ✓ | ✓ |
| dn40 × 48 | ✓ | ✓ |
| dn50 × 42 | ✓ | ✓ |
| dn50 × 48 | ✓ | ✓ |
| dn63 × 34 | ✓ | ✓ |
| dn63 × 42 | ✓ | ✓ |
| dn63 × 48 | ✓ | ✓ |
| dn63 × 60 | ✓ | ✓ |
Bent transitions, 1.5 m steel end
The same fitting with a longer steel end, 1.5 m made of a 0.3 m and a 1.2 m section. It is the one to use where the riser has further to go, or where the PE has to stay under a deeper cover.
Bent Steel-to-PE Transition, Plain Steel End, 1.5 mdn25–dn63 · 19 sizes
19 combinations, dn25 to dn63, the widest of the bent tables.
| Size | Standard Coating | 3PE Coating | Size | Standard Coating | 3PE Coating |
|---|---|---|---|---|---|
| dn25 × 22 | ✓ | ✓ | dn40 × 48 | ✓ | ✓ |
| dn25 × 27 | ✓ | ✓ | dn50 × 42 | ✓ | ✓ |
| dn32 × 22 | ✓ | ✓ | dn50 × 48 | ✓ | ✓ |
| dn32 × 27 | ✓ | ✓ | dn63 × 34 | ✓ | ✓ |
| dn32 × 32 | ✓ | ✓ | dn63 × 38 | ✓ | ✓ |
| dn32 × 34 | ✓ | ✓ | dn63 × 42 | ✓ | ✓ |
| dn40 × 32 | ✓ | ✓ | dn63 × 48 | ✓ | ✓ |
| dn40 × 34 | ✓ | ✓ | dn63 × 57 | ✓ | ✓ |
| dn40 × 38 | ✓ | ✓ | dn63 × 60 | ✓ | ✓ |
| dn40 × 42 | ✓ | ✓ |
Bent Threaded Steel-to-PE Transition, 1.5 mdn25–dn63 · 14 sizes
14 combinations, dn25 to dn63. Threaded steel end.
| Size | Standard Coating | 3PE Coating |
|---|---|---|
| dn25 × 22 | ✓ | ✓ |
| dn25 × 27 | ✓ | ✓ |
| dn32 × 22 | ✓ | ✓ |
| dn32 × 27 | ✓ | ✓ |
| dn32 × 34 | ✓ | ✓ |
| dn40 × 34 | ✓ | ✓ |
| dn40 × 42 | ✓ | ✓ |
| dn40 × 48 | ✓ | ✓ |
| dn50 × 42 | ✓ | ✓ |
| dn50 × 48 | ✓ | ✓ |
| dn63 × 34 | ✓ | ✓ |
| dn63 × 42 | ✓ | ✓ |
| dn63 × 48 | ✓ | ✓ |
| dn63 × 60 | ✓ | ✓ |
How to specify a transition
- PE size and series: dn and SDR. Both straight families are split by series, so this decides the family.
- Steel size: every row lists the PE size against the steel DN it takes, and one PE size often takes two or three different steel sizes. Give the steel pipe size, not just the PE size.
- Steel end: plain for welding, or threaded. If threaded, give the standard.
- Shape and length: straight, or bent in 1.1 m or 1.5 m.
- Coating: standard or 3PE. Say if the coating has to be extended over the weld zone on site.
- Material: carbon steel is standard. Stainless is made to order and quoted separately.
Frequently asked questions
Can you supply the transition in stainless steel?
Yes, made to order and quoted per project. The six families on this page are carbon steel as standard, in standard coating or 3PE. If the specification calls for stainless, raise it at enquiry stage: the lead time is longer than the tables suggest because it is not a stock item.
What do the two numbers in the size mean, like dn63 × 42?
The first is the PE outside diameter, the second is the steel size. One PE size takes several steel sizes, which is why the tables list the combinations rather than a single range.
What is the difference between the 1.1 m and 1.5 m bent transitions?
The steel end length: 1.1 m is made of a 0.3 m and a 0.8 m section, 1.5 m of a 0.3 m and a 1.2 m section. The longer one is used where the riser has further to reach or the PE has to stay deeper.
Standard coating or 3PE?
Standard coating for normal buried service. 3PE where the ground is aggressive or the steel end is exposed, and where the coating will be inspected and repaired if damaged. Both are listed for every size in the tables.
Is the PE end electrofusion or butt fusion?
The straight and bent transitions in our range are butt fusion on the PE side, which is why every family is listed by SDR. Butt fusion is what gives the full-section joint at the PE end of a transition.
- HDPE flange adaptor dimensions – the other way to make a bolted connection
- HDPE fittings specifications – all 65 families, transitions included
- HDPE fittings for gas distribution – where most transitions end up
- HDPE fittings for water supply – the water-side view of the range
- How HDPE pipes are joined – the PE end of the joint














