Every HDPE tee we mould in-house is listed here by fusion method, with the size range and the wall series each body is made for. The tables come from our own tooling list rather than from a third-party catalogue, so a size is either something we run or it is not on the page. Equal, reducing, lateral and threaded tees are covered, in dn20 to dn1600.
Size range at a glance
| Fusion method | Tee type | Size range | Sizes | Wall series |
|---|---|---|---|---|
| Electrofusion | Equal tee | dn25 – dn630 | 25 | SDR 9 / 11 / 17 |
| Reducing tee | dn25 – dn630 | 79 | SDR 9 / 11 | |
| Butt fusion | Equal tee | dn40 – dn1600 | 27 | SDR 11 / 17 |
| Reducing tee | dn50 – dn1600 | 102 | SDR 11 / 17 | |
| Lateral tee 45° | dn63 – dn160 | 6 | SDR 11 | |
| Socket fusion | Equal tee | dn20 – dn63 | 6 | SDR 11 |
| Reducing tee | dn25 – dn63 | 15 | SDR 11 | |
| Socket fusion, threaded | Female threaded tee | dn20 – dn63 | 6 | SDR 11 |
| Male threaded tee | dn20 – dn63 | 6 | SDR 11 |
Full tables for each line follow. The gas distribution series is listed separately at the end, because those bodies are moulded to SDR11 and SDR17 only.
Electrofusion tees
An electrofusion tee carries a heating coil inside each socket. The welder applies a fixed voltage for a set time and the coil melts the fitting and the pipe wall together across the full socket length. Nothing rotates and nothing is pushed, which is what makes it usable in a trench where the pipe cannot be moved.
Electrofusion Equal Teedn25–dn630 · 25 sizes
Three sockets, all the same size. The most common item on a water or gas tie-in, and the one we hold most stock of in dn63 to dn315.
| Size | SDR Series | Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|---|---|
| dn25 | 11/9 | dn110 | 17/11/9 | dn250 | 17/11/9 | dn630 | 11 |
| dn32 | 11/9 | dn125 | 11/9 | dn280 | 11# | dn450 | 17 |
| dn40 | 11/9 | dn140 | 11# | dn315 | 17/11/9 | dn500 | 17 |
| dn50 | 11/9 | dn160 | 17/11/9 | dn355 | 11/17 | dn630 | 17 |
| dn63 | 11/9 | dn180 | 11# | dn400 | 11 | ||
| dn75 | 11/9 | dn200 | 17/11/9 | dn450 | 11 | ||
| dn90 | 11/9 | dn225 | 17/11 | dn500 | 11 |
Electrofusion Reducing Teedn25–dn630 · 79 sizes
Main run first, branch second. 79 combinations from dn25 × 20 up to dn630. If the branch you need is not listed, the run size is usually still available and the branch can be moulded on request.
| Size | SDR Series | Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|---|---|
| dn25 × 20 | 11 | dn90 × 63 | 11/9 | dn200 × 90 | 11/9 | dn400 × 315 | 11 |
| dn32 × 20 | 11 | dn90 × 75 | 11/9 | dn200 × 110 | 11/9 | dn450 × 160 | 11 |
| dn32 × 25 | 11 | dn110 × 32 | 11/9 | dn200 × 160 | 11/9 | dn450 × 250 | 11 |
| dn40 × 20 | 11 | dn110 × 40 | 11/9 | dn225 × 110 | 11 | dn450 × 315 | 11 |
| dn40 × 25 | 11 | dn110 × 50 | 11/9 | dn225 × 160 | 11 | dn500 × 200 | 11 |
| dn40 × 32 | 11/9 | dn110 × 63 | 11/9 | dn225 × 200 | 11 | dn500 × 315 | 11 |
| dn50 × 25 | 11/9 | dn110 × 75 | 11/9 | dn250 × 90 | 11/9 | dn500 × 400 | 11 |
| dn50 × 32 | 11/9 | dn110 × 90 | 11/9 | dn250 × 110 | 11/9 | dn630 × 315 | 11 |
| dn50 × 40 | 11/9 | dn125 × 90 | 11 | dn250 × 160 | 11/9 | dn630 × 400 | 11 |
| dn63 × 25 | 11/9 | dn125 × 110 | 11 | dn250 × 200 | 11/9 | dn630 × 500 | 11 |
| dn63 × 32 | 11/9 | dn140 × 63 | 11# | dn280 × 160 | 11# | dn450 × 250 | 17 |
| dn63 × 40 | 11/9 | dn140 × 110 | 11# | dn315 × 110 | 11/9 | dn450 × 315 | 17 |
| dn63 × 50 | 11/9 | dn160 × 50 | 11 | dn315 × 160 | 11/9 | dn450 × 400 | 17 |
| dn75 × 32 | 11/9 | dn160 × 63 | 11/9 | dn315 × 200 | 11/9 | dn500 × 315 | 17 |
| dn75 × 40 | 11/9 | dn160 × 75 | 11/9 | dn315 × 250 | 11/9 | dn500 × 400 | 17 |
| dn75 × 50 | 11/9 | dn160 × 90 | 11/9 | dn355 × 200 | 11 | dn500 × 450 | 17 |
| dn75 × 63 | 11/9 | dn160 × 110 | 11/9 | dn355 × 250 | 11 | dn630 × 400 | 17 |
| dn90 × 32 | 11/9 | dn180 × 110 | 11# | dn355 × 315 | 11 | dn630 × 450 | 17 |
| dn90 × 40 | 11/9 | dn200 × 63 | 11/9 | dn400 × 200 | 11 | dn630 × 500 | 17 |
| dn90 × 50 | 11/9 | dn200 × 75 | 11/9 | dn400 × 250 | 11 |
Butt fusion tees
A butt fusion tee starts as a plain moulded body. The ends are faced square on the facing machine, heated on a plate, and pushed together, so the joint is a full-section weld with the same wall thickness as the pipe. It is the only method that covers the large sizes.
Butt Fusion Equal Teedn40–dn1600 · 27 sizes
dn40 to dn1600, the widest tee range we hold. Above dn630 this is the only practical option.
The mm figures for every one of those 27 sizes are printed on the butt fusion equal tee dimension table: run bore depths L1 and L2, branch bore depth L3 and the centre-to-end length L for dn40 to dn1600, in SDR11 and SDR17, straight off the Style B drawing.
| Size | SDR Series | Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|---|---|
| dn40 | 11 | dn140 | 11/17 | dn315 | 9/11/17 | dn710 | 11/17 |
| dn50 | 11 | dn160 | 11/17 | dn355 | 11/17 | dn800 | 11/17 |
| dn63 | 11 | dn180 | 11/17 | dn400 | 9/11/17 | dn900# | 17 |
| dn75 | 11 | dn200 | 11/17 | dn450 | 11/17 | dn1000 | 17 |
| dn90 | 11/17 | dn225 | 11/17 | dn500 | 11/17 | dn1200# | 17 |
| dn110 | 11/17 | dn250 | 11/17 | dn560 | 11/17 | dn1600 | 17 |
| dn125 | 11/17 | dn280 | 11/17 | dn630 | 11/17 |
Butt Fusion Reducing Teedn50–dn1600 · 102 sizes
102 combinations up to dn1600 on the run – the largest reducing tee list on the site.
| Size | SDR Series | Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|---|---|
| dn50 × 25 | 11 | dn125 × 110 | 11/17 | dn225 × 110 | 11/17 | dn400 × 315 | 11/17 |
| dn50 × 32 | 11 | dn140 × 63# | 11/17 | dn225 × 160 | 11/17 | dn450 × 250 | 11/17 |
| dn50 × 40 | 11 | dn140 × 90# | 11/17 | dn225 × 200 | 11/17 | dn450 × 315 | 11/17 |
| dn63 × 25 | 11 | dn140 × 110 | 11/17 | dn250 × 90 | 11/17 | dn450 × 400 | 11/17 |
| dn63 × 32 | 11 | dn160 × 32 | 11/17 | dn250 × 110 | 11/17 | dn500 × 315 | 11/17 |
| dn63 × 40 | 11 | dn160 × 40 | 11/17 | dn250 × 125 | 11/17 | dn500 × 400 | 11/17 |
| dn63 × 50 | 11 | dn160 × 50 | 11/17 | dn250 × 160 | 11/17 | dn500 × 450 | 11/17 |
| dn75 × 32 | 11 | dn160 × 63 | 11/17 | dn250 × 200 | 11/17 | dn630 × 400 | 11/17 |
| dn75 × 40 | 11 | dn160 × 75 | 11/17 | dn250 × 225 | 11/17 | dn630 × 450 | 11/17 |
| dn75 × 50 | 11 | dn160 × 90 | 11/17 | dn280 × 110 | 11/17 | dn630 × 500 | 11/17 |
| dn75 × 63 | 11 | dn160 × 110 | 11/17 | dn280 × 160 | 11/17 | dn710 × 400 | 11/17 |
| dn90 × 25 | 11/17 | dn160 × 125 | 11/17 | dn280 × 200 | 11/17 | dn710 × 500 | 11/17 |
| dn90 × 32 | 11/17 | dn180 × 90 | 11/17 | dn280 × 225 | 11/17 | dn710 × 630 | 11/17 |
| dn90 × 40 | 11/17 | dn180 × 110 | 11/17 | dn315 × 110 | 11/17 | dn800 × 500 | 11/17 |
| dn90 × 50 | 11/17 | dn180 × 160 | 11/17 | dn315 × 160 | 11/17 | dn800 × 630 | 11/17 |
| dn90 × 63 | 11/17 | dn200 × 40 | 11/17 | dn315 × 200 | 11/17 | dn800 × 710 | 11/17 |
| dn90 × 75 | 11/17 | dn200 × 50 | 11/17 | dn315 × 225 | 11/17 | dn1000 × 500 | 17 |
| dn110 × 32 | 11/17 | dn200 × 63 | 11/17 | dn315 × 250 | 11/17 | dn1000 × 630 | 17 |
| dn110 × 40 | 11/17 | dn200 × 75 | 11/17 | dn355 × 160 | 11/17 | dn1000 × 800 | 17 |
| dn110 × 50 | 11/17 | dn200 × 90 | 11/17 | dn355 × 200 | 11/17 | dn1200 × 630# | 17 |
| dn110 × 63 | 11/17 | dn200 × 110 | 11/17 | dn355 × 250 | 11/17 | dn1200 × 800# | 17 |
| dn110 × 75 | 11/17 | dn200 × 125 | 11/17 | dn355 × 315 | 11/17 | dn1200 × 1000# | 17 |
| dn110 × 90 | 11/17 | dn200 × 160 | 11/17 | dn400 × 110 | 11/17 | dn1600 × 630 | 17 |
| dn125 × 63 | 11/17 | dn225 × 63 | 11/17 | dn400 × 160 | 11/17 | dn1600 × 1000 | 17 |
| dn125 × 75 | 11/17 | dn225 × 75 | 11/17 | dn400 × 200 | 11/17 | ||
| dn125 × 90 | 11/17 | dn225 × 90 | 11/17 | dn400 × 250 | 11/17 |
Butt Fusion Lateral Tee (45°)dn63–dn160 · 6 sizes
A Y-shaped outlet at 45° instead of 90°. Used where the branch has to follow the main direction, typically on dn63 to dn160.
| Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|
| dn63 | 11 | dn90 | 11 | dn125 | 11 |
| dn75 | 11 | dn110 | 11 | dn160 × 75 | 17 |
Socket fusion tees
Socket fusion is for small diameters: a heated male tool forms a socket in the pipe end and the tee is pushed on while both are molten. It is fast and needs no clamping, which suits service lines and irrigation. It stops at dn63 – above that the insertion force becomes impractical.
Socket Fusion Teedn20–dn63 · 6 sizes
dn20 to dn63, equal pattern.
| Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|
| dn20 | 11 | dn32 | 11 | dn50 | 11 |
| dn25 | 11 | dn40 | 11 | dn63 | 11 |
Socket Fusion Reducing Teedn25–dn63 · 15 sizes
15 main-run and branch combinations, dn25 × 20 to dn63.
| Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|
| dn25 × 20 | 11 | dn40 × 32 | 11 | dn63 × 20 | 11 |
| dn32 × 20 | 11 | dn50 × 20 | 11 | dn63 × 25 | 11 |
| dn32 × 25 | 11 | dn50 × 25 | 11 | dn63 × 32 | 11 |
| dn40 × 20 | 11 | dn50 × 32 | 11 | dn63 × 40 | 11 |
| dn40 × 25 | 11 | dn50 × 40 | 11 | dn63 × 50 | 11 |
Socket Fusion Threaded Teesdn20–dn63 · 6 + 6 sizes
One side sockets onto PE, the other carries a BSPP or BSPT thread, so the tee can take a metal valve, gauge or hose connection without a further adaptor. Female and male patterns are both moulded. State the thread standard when ordering – BSPP and NPT are not interchangeable.
| Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|
| dn20 × 1/2″ | 11 | dn32 × 1″ | 11 | dn50 × 1-1/2″ | 11 |
| dn25 × 3/4″ | 11 | dn40 × 1-1/4″ | 11 | dn63 × 2″ | 11 |
| Size | SDR Series | Size | SDR Series | Size | SDR Series |
|---|---|---|---|---|---|
| dn20 × 1/2″ | 11 | dn32 × 1″ | 11 | dn50 × 1-1/2″ | 11 |
| dn25 × 3/4″ | 11 | dn40 × 1-1/4″ | 11 | dn63 × 2″ | 11 |
PE100 gas distribution series
Gas networks use a separate set of bodies, moulded to SDR11 and SDR17 and dimensioned for the yellow PE100 gas range. They are not interchangeable with the water series even where the dn size matches, so order by series and not by size alone.
Electrofusion Equal Tee (gas)dn25–dn400 · 16 sizes
| Size | SDR11 | SDR17 | Size | SDR11 | SDR17 |
|---|---|---|---|---|---|
| dn25 | ✓ | - | dn125 | ✓ | - |
| dn32 | ✓ | - | dn160 | ✓ | - |
| dn40 | ✓ | - | dn200 | ✓ | - |
| dn50 | ✓ | - | dn225 | ✓ | - |
| dn63 | ✓ | - | dn250 | ✓ | - |
| dn75 | ✓ | - | dn315 | ✓ | - |
| dn90 | ✓ | - | dn355 | ✓ | ✓ |
| dn110 | ✓ | - | dn400 | ✓ | ✓ |
Electrofusion Reducing Tee (gas)dn25–dn400 · 56 sizes
| Size | SDR11 | SDR17 | Size | SDR11 | SDR17 |
|---|---|---|---|---|---|
| dn25 × 20 × 25 | ✓ | - | dn125 × 90 × 125 | ✓ | - |
| dn32 × 20 × 32 | ✓ | - | dn160 × 50 × 160 | ✓ | - |
| dn32 × 25 × 32 | ✓ | - | dn160 × 63 × 160 | ✓ | - |
| dn40 × 20 × 40 | ✓ | - | dn160 × 75 × 160 | ✓ | - |
| dn40 × 25 × 40 | ✓ | - | dn160 × 90 × 160 | ✓ | - |
| dn40 × 32 × 40 | ✓ | - | dn160 × 110 × 160 | ✓ | - |
| dn50 × 25 × 50 | ✓ | - | dn200 × 63 × 200 | ✓ | - |
| dn50 × 32 × 50 | ✓ | - | dn200 × 75 × 200 | ✓ | - |
| dn50 × 40 × 50 | ✓ | - | dn200 × 90 × 200 | ✓ | - |
| dn63 × 25 × 63 | ✓ | - | dn200 × 110 × 200 | ✓ | - |
| dn63 × 32 × 63 | ✓ | - | dn200 × 160 × 200 | ✓ | - |
| dn63 × 40 × 63 | ✓ | - | dn225 × 110 × 225 | ✓ | - |
| dn63 × 50 × 63 | ✓ | - | dn225 × 160 × 225 | ✓ | - |
| dn75 × 32 × 75 | ✓ | - | dn225 × 200 × 225 | ✓ | - |
| dn75 × 40 × 75 | ✓ | - | dn250 × 90 × 250 | ✓ | - |
| dn75 × 50 × 75 | ✓ | - | dn250 × 110 × 250 | ✓ | - |
| dn75 × 63 × 75 | ✓ | - | dn250 × 160 × 250 | ✓ | - |
| dn90 × 32 × 90 | ✓ | - | dn250 × 200 × 250 | ✓ | - |
| dn90 × 40 × 90 | ✓ | - | dn315 × 110 × 315 | ✓ | - |
| dn90 × 50 × 90 | ✓ | - | dn315 × 160 × 315 | ✓ | - |
| dn90 × 63 × 90 | ✓ | - | dn315 × 200 × 315 | ✓ | - |
| dn90 × 75 × 90 | ✓ | - | dn315 × 250 × 315 | ✓ | - |
| dn110 × 32 × 110 | ✓ | - | dn355 × 200 × 355 | ✓ | - |
| dn110 × 40 × 110 | ✓ | - | dn355 × 250 × 355 | ✓ | - |
| dn110 × 50 × 110 | ✓ | - | dn355 × 315 × 355 | ✓ | - |
| dn110 × 63 × 110 | ✓ | - | dn400 × 200 × 400 | ✓ | - |
| dn110 × 75 × 110 | ✓ | - | dn400 × 250 × 400 | ✓ | - |
| dn110 × 90 × 110 | ✓ | - | dn400 × 315 × 400 | ✓ | - |
Butt Fusion Equal Tee (gas)dn50–dn630 · 24 sizes
| Size | SDR11 | SDR17 | Size | SDR11 | SDR17 |
|---|---|---|---|---|---|
| dn50 × 50 × 50 | ✓ | - | dn280 × 280 × 280 | ✓ | ✓ |
| dn63 × 63 × 63 | ✓ | - | dn315 × 315 × 315 | ✓ | ✓ |
| dn75 × 75 × 75 | ✓ | - | dn355 × 355 × 355 | ✓ | ✓ |
| dn90 × 90 × 90 | ✓ | ✓ | dn400 × 400 × 400 | ✓ | ✓ |
| dn110 × 110 × 110 | ✓ | ✓ | dn450 × 450 × 450 | ✓ | ✓ |
| dn125 × 125 × 125 | ✓ | ✓ | dn500 × 500 × 500 | ✓ | ✓ |
| dn140 × 140 × 140 | ✓ | ✓ | dn560 × 560 × 560 | ✓ | ✓ |
| dn160 × 160 × 160 | ✓ | ✓ | dn630 × 630 × 630 | ✓ | ✓ |
| dn180 × 180 × 180 | ✓ | ✓ | dn450 × 450 × 450 (long pattern) | - | ✓ |
| dn200 × 200 × 200 | ✓ | ✓ | dn500 × 500 × 500 (long pattern) | - | ✓ |
| dn225 × 225 × 225 | ✓ | ✓ | dn560 × 560 × 560 (long pattern) | - | ✓ |
| dn250 × 250 × 250 | ✓ | ✓ | dn630 × 630 × 630 (long pattern) | - | ✓ |
Butt Fusion Reducing Tee (gas)dn75–dn400 · 64 sizes
| Size | SDR11 | SDR17 | Size | SDR11 | SDR17 |
|---|---|---|---|---|---|
| dn75 × 32 × 75 | ✓ | - | dn200 × 63 × 200 | ✓ | ✓ |
| dn75 × 40 × 75 | ✓ | - | dn200 × 75 × 200 | ✓ | ✓ |
| dn75 × 50 × 75 | ✓ | - | dn200 × 90 × 200 | ✓ | ✓ |
| dn75 × 63 × 75 | ✓ | - | dn200 × 110 × 200 | ✓ | ✓ |
| dn90 × 32 × 90 | ✓ | ✓ | dn200 × 125 × 200 | ✓ | ✓ |
| dn90 × 40 × 90 | ✓ | ✓ | dn200 × 160 × 200 | ✓ | ✓ |
| dn90 × 50 × 90 | ✓ | ✓ | dn225 × 90 × 225 | ✓ | ✓ |
| dn90 × 63 × 90 | ✓ | ✓ | dn225 × 110 × 225 | ✓ | ✓ |
| dn90 × 75 × 90 | ✓ | ✓ | dn225 × 160 × 225 | ✓ | ✓ |
| dn110 × 32 × 110 | ✓ | ✓ | dn225 × 200 × 225 | ✓ | ✓ |
| dn110 × 40 × 110 | ✓ | ✓ | dn250 × 90 × 250 | ✓ | ✓ |
| dn110 × 50 × 110 | ✓ | ✓ | dn250 × 110 × 250 | ✓ | ✓ |
| dn110 × 63 × 110 | ✓ | ✓ | dn250 × 125 × 250 | ✓ | ✓ |
| dn110 × 75 × 110 | ✓ | ✓ | dn250 × 160 × 250 | ✓ | ✓ |
| dn110 × 90 × 110 | ✓ | ✓ | dn250 × 200 × 250 | ✓ | ✓ |
| dn125 × 63 × 125 | ✓ | ✓ | dn250 × 225 × 250 | ✓ | ✓ |
| dn125 × 75 × 125 | ✓ | ✓ | dn280 × 110 × 280 | ✓ | ✓ |
| dn125 × 90 × 125 | ✓ | ✓ | dn280 × 160 × 280 | ✓ | ✓ |
| dn125 × 110 × 125 | ✓ | ✓ | dn280 × 200 × 280 | ✓ | ✓ |
| dn140 × 110 × 140 | ✓ | ✓ | dn280 × 225 × 280 | ✓ | ✓ |
| dn160 × 32 × 160 | ✓ | ✓ | dn315 × 110 × 315 | ✓ | ✓ |
| dn160 × 40 × 160 | ✓ | ✓ | dn315 × 160 × 315 | ✓ | ✓ |
| dn160 × 50 × 160 | ✓ | ✓ | dn315 × 200 × 315 | ✓ | ✓ |
| dn160 × 63 × 160 | ✓ | ✓ | dn315 × 225 × 315 | ✓ | ✓ |
| dn160 × 75 × 160 | ✓ | ✓ | dn315 × 250 × 315 | ✓ | ✓ |
| dn160 × 90 × 160 | ✓ | ✓ | dn355 × 160 × 355 | ✓ | ✓ |
| dn160 × 110 × 160 | ✓ | ✓ | dn355 × 200 × 355 | ✓ | ✓ |
| dn160 × 125 × 160 | ✓ | ✓ | dn400 × 110 × 400 | ✓ | ✓ |
| dn180 × 110 × 180 | ✓ | ✓ | dn400 × 160 × 400 | ✓ | ✓ |
| dn180 × 160 × 180 | ✓ | ✓ | dn400 × 200 × 400 | ✓ | ✓ |
| dn200 × 40 × 200 | ✓ | ✓ | dn400 × 250 × 400 | ✓ | ✓ |
| dn200 × 50 × 200 | ✓ | ✓ | dn400 × 315 × 400 | ✓ | ✓ |
How to specify a tee
A tee order needs five things, and a missing one is the usual reason a quotation comes back with a question:
- Main run size – dn, outside diameter.
- Branch size – the same as the run for an equal tee.
- Wall series – SDR 11, 17 or 9. This sets the socket depth and the pressure rating.
- Fusion method – electrofusion, butt fusion or socket fusion. It decides the body, not just the end preparation.
- Standard or drawing – if the tee has to mate with an existing line, send the drawing or the pipe SDR and OD tolerance.
How to read these tables
- SDR series – the wall thickness series the fitting is made for. Where two or three are listed (for example
17/11/9), the same body is moulded for each of those series. - dn90 × 63 – a reducing item: the main run is dn90 and the branch or outlet is dn63.
- dn110 × 63 in a saddle table – the outlet saddle for a dn110 main with a dn63 branch.
- Sizes are in mm and are outside diameters (OD) unless a DN figure is given for a steel end.
- ✓ / – in the gas and valve tables: available, or not listed in that series. – means not in the standard range, not that it cannot be made – ask us.
- * after a size – machined from the next larger butt fusion body rather than moulded. Same dimensions and same pressure rating, longer lead time.
- # – that mould was in development when this page was published, whether the mark sits on a size or in the series column. Confirm the lead time with us before you put it in a tender.
| SDR series | SDR 17 | SDR 11 | SDR 9 |
|---|---|---|---|
| Nominal pressure | PN 10 | PN 16 | PN 20 |
| Typical service | Water distribution, gravity and low pressure | General pressure pipe, gas distribution | Higher pressure, industrial lines |
Frequently asked questions
What is the difference between an equal tee and a reducing tee?
An equal tee has the same diameter on the run and the branch, so it splits a line into two identical legs. A reducing tee keeps the run at one size and steps the branch down – dn110 × 63, for example, takes a 63 mm branch off a 110 mm main. Reducing tees are listed with both figures, main run first.
How large a tee can you supply in one piece?
Butt fusion equal tees go to dn1600 and butt fusion reducing tees to dn1600 on the run. Electrofusion tees stop at dn630 because the coil and terminal arrangement becomes impractical above that, which is why large sizes are butt fusion only. For dn1600 we are among the few Chinese manufacturers producing the size.
Do you make tapping tees and saddle tees?
Yes, but they sit in a different family: an outlet is fusion-welded onto the outside of an existing main rather than the line being cut in. Those are listed on our tapping tee and saddle pages, and the branch sizes follow the saddle tables.
Can a tee be supplied with a different branch angle?
45° lateral tees are a standard mould up to dn160 on the run. Other angles need a new mould – the tooling cost is a one-off and we quote it separately from the parts.
- All 65 fitting families on one page – HDPE pipe fittings specifications
- HDPE elbow dimensions · HDPE reducer size chart · HDPE flange adaptor dimensions
- Products – butt fusion tees · electrofusion tees · socket fusion fittings
- How HDPE pipes are joined














