PE Flange HDPE Pipe Fittings SDR11 PN16 ISO4427

PE Flange HDPE Pipe Fittings SDR11 PN16 ISO4427

A PE flange is an HDPE pipe fitting that converts a fused polyethylene line into a bolted mechanical connection. One end is a fusion-readied flange neck that is heat-jointed directly onto the pipe, while the other end presents a standard flat flange face for bolting to valves, pumps and adjacent equipment. Made from the same PE100 material as the pipe, it keeps the whole run all-polymer, corrosion-free and pressure-rated from DN40 up to DN1600.
Send Inquiry

PE Flange HDPE Pipe Fittings SDR11 PN16

butt-fusion-flange-dimensions

 

Fusion-Readied Flange Neck

The fitted end is prepared for either electrofusion or butt fusion, so the joint becomes one continuous, leak-tight material transition rather than a mechanical seal. Because the flange shares the pipe's PE100 grade, the weld develops full-strength continuity and resists corrosion, electrolytic coupling and long-term buried degradation.

Flange Adapter to Mechanical Connection

The bolt face lets the plastic line stop cleanly at a flanged valve, pump suction, pressure-test header or tie-in to other materials. For buried and above-ground duty, a backing ring and gasket complete a dressable joint that can be opened later for maintenance without cutting the pipe.

Size Coverage DN40 & Small Bores to DN1600

The standard flange series runs from DN40 to DN630 for everyday distribution bores, while a separate large-bore series in SDR11 and SDR17 extends up to DN1600 for heavy transmission and distribution mains \u2014 letting one flange specification cover the whole network.

 

Flange Adapter Size Ranges, Stub and Steel Ring

A PE flange connection is made from two parts: the adapter, which is welded to the pipe and carries the sealing face, and the steel backing ring, which is loose and takes the bolt load. The adapter is ordered by pipe diameter and wall series; the ring is ordered by diameter and pressure rating, and the two are matched at the drawing stage. Both schedules are printed below.

Electrofusion flange adapter, dn50 to dn800

SizeSDR SeriesSizeSDR SeriesSizeSDR SeriesSizeSDR Series
dn5011/9dn12511dn31511/17dn56011/17
dn6311/9dn16011/9dn35511/17dn63017
dn7511/9dn20017/11/9dn40011/17dn71017
dn9011/9dn22517/11dn45011/17dn80017
dn11011/9dn25017/11/9dn50011/17

Butt fusion flange adapter, dn40 to dn1600

SizeSDR SeriesSizeSDR SeriesSizeSDR SeriesSizeSDR Series
dn4011dn14011/17dn31511/17dn71011/17
dn5011dn16011/17dn35511/17dn80011/17
dn6311dn18011/17dn40011/17dn90011/17
dn7511dn20011/17dn45011/17dn100011/17
dn9011/17dn22511/17dn50011/17dn120011/17
dn11011/17dn25011/17dn56011/17dn1400#17
dn12511/17dn28011/17dn63011/17dn160017

The adapter is welded with the same cycle as any other fitting in its family, which is why the electrofusion version stops at dn800 while the butt fusion one carries on to dn1600. Wall series is confirmed against the pipe as usual, and the heavy series reaches further down the range than the light one. The backing ring is a separate line item and is specified by nominal pressure rather than by wall series, because a ring of a given rating fits adapters of more than one series at the same diameter. For the ring schedule itself, the full fitting list, or the pressure classes available at each size, see the HDPE butt fusion end cap page and the specifications page.

Every PE Flange HDPE Pipe Fittings SDR11 PN16 ISO4427 we ship comes from our own injection lines and is tested in a CNAS-accredited laboratory before despatch. Find out more about Qingfa Industry.

Hot Tags: PE Flange HDPE Pipe Fittings SDR11 PN16 ISO4427, PE Flange HDPE Pipe Fittings SDR11 PN16 ISO4427 dn40-dn630, PE100 pe flange hdpe pipe fittings sdr11 pn16 iso4427, pe flange hdpe pipe fittings sdr11 pn16 iso4427 supplier, Electrofusion Test Cap, End Cap HDPE, HDPE Cap, HDPE End Cap, HDPE End Plug, HDPE PiPE End Cap

Previous:No Information
Next:No Information

Send Inquiry