Butt Fusion Welding Parameters For HDPE Pipe: Temperature, Pressure, Time And Bead Size

Nov 03, 2026

Leave a message

Butt Fusion · Parameters
Butt Fusion Welding Parameters For HDPE Pipe: Temperature, Pressure, Time And Bead Size

Four values decide whether an HDPE joint holds: plate temperature, the three pressures, the four time values, and the bead that forms while the first three are working. Get them right and the joint outlives the pipe. Get them roughly right and the joint passes a pressure test and fails a year later.

The values below are the ones we issue with our machines, plus the way crews adjust them when the site is not a laboratory. Method selection first: butt fusion or electrofusion.

225 ± 10 °C
Plate temperature, PE100
10 s / mm
Heat soak, field rule
5 s
Maximum changeover, dn160
Temperature

Plate Temperature Depends On The Compound, Not On Habit

220 °C is not universal, and a crew that welds at 220 °C summer and winter is guessing. The plate temperature follows the compound grade, because melt behaviour differs between them. PE100 and PE80 do not fuse on the same schedule.

Pipe grade Plate temperature Note
PE100 225 ± 10 °C Standard condition, ambient 5-35 °C
PE80 210 ± 10 °C Lower melt flow, lower plate setting
Ambient below 5 °C +5 to +10 °C Compensates heat loss in transfer
Above 38 °C, direct sun -5 to -10 °C Avoids surface degradation

Measure the plate with a contact thermometer, not the controller display. A plate reading 225 °C on screen and 205 °C at the surface produces cold fusion on every joint of the shift, and nothing on the machine will tell the operator.

Time

The Four Time Values And When Each One Starts

Value Field rule What it controls
Bead-up Until bead reaches 0.5 + 0.1 x e (mm) Proves full face contact before timing
Heat soak 10 x e seconds, e in mm Heat penetration to fusion depth
Changeover 5 s small bore, 8 s above dn250 Limits melt surface cooling
Cooling under pressure 1 min per mm of wall + 3-4 min Strength development

Two mistakes account for most weak joints, and both are timing:

  • The timer starts after the bead, not when the plate touches. Pressurise until the collar forms, drop to drag pressure, then count. Timing from first contact adds an uncontrolled 10 to 40 seconds of extra heat.
  • Cooling is not optional waiting. Release pressure early and the interface relaxes while still molten. The bead looks fine, the cut face shows voids, and the bend test opens it.
Worked Example

dn160 SDR11, PE100: The Full Set Of Numbers

  • Wall thickness e = 14.6 mm
  • Bead-up height target = 0.5 + 0.1 x 14.6 ≈ 1.96 mm
  • Heat soak = 10 x 14.6 = 146 s
  • Changeover ≤ 5 s
  • Cooling under pressure = 14.6 + 3 ≈ 17.6 min
  • Finished bead height = 0.2 to 0.25 x 14.6 ≈ 2.9 to 3.7 mm

That cooling time is why a crew on dn160 completes 15 to 18 joints in an eight-hour day once facing, alignment and inspection are added. Crews reporting 40 joints on the same diameter are shortening cooling, and the leak appears after backfill rather than before it.

Inspection

Bead Geometry Is The Only In-Process Evidence

Check Target What a deviation means
Bead height 0.20 to 0.25 x e Low: under-heated or low pressure. High: over-pressure
Bead width Even all round Uneven: misalignment or unequal plate contact
Bead root Smooth transition, no notch Sharp notch concentrates stress
Bead layers One homogeneous mass Layered or stepped: false fusion
Cut section No voids, no unbonded line Any visible interface line: reject

Photograph the bead before backfill. On disputed projects bead photographs settle the question faster than any test report, and they cost nothing to keep. Joint acceptance is normally confirmed later by hydrostatic pressure testing.

Site Conditions

Adjustments For Wind, Rain, Heat And Cold

Condition Adjustment
Wind above 15 km/h Shelter the machine, +5 °C plate, shortest changeover
Rain Stop. Water on plate or end face guarantees a cold joint
Below 5 °C ambient +5 to +10 °C plate, +10 to +20 % heat soak, longer cooling
Above 38 °C -5 to -10 °C plate, +20 % cooling, shade the pipe
Pipe stored in sun vs shade 20 to 30 °C surface difference: let it equalise

The machine does not know any of this. Parameter discipline is a human task, and it is the reason two crews with identical equipment produce different joint quality on the same main.

Note

The Wall x 10 Rule Is An Approximation

10 seconds per millimetre is a field rule, not a standard value. ASTM F2620 and ISO 21307 publish heat soak tables by wall thickness and pressure regime, and they diverge from the linear rule at both extremes: thin walls are relatively over-heated by the formula, thick walls slightly under-heated. Use the rule for planning and the manufacturer's table for the welding procedure specification.

Our machines ship with the plate thermometer, the three-pressure schedule and the bead chart, so the crew is not converting formulas on the trench edge. See the butt fusion and electrofusion ranges.

FAQ

Frequently Asked Questions

What is the heat soak time for 160 mm PE pipe?

For dn160 SDR11, e = 14.6 mm, the field rule gives 146 seconds. Confirm against your welding procedure: the accepted range typically falls between 140 and 170 seconds depending on the standard applied.

Can I weld HDPE at 200 °C if the plate heats slowly?

No. Lower plate temperature at the same heat soak time under-heats the interface. Repair or replace the heater, do not compensate with time.

Why does a joint look perfect and fail a bend test?

Changeover time or a contaminated end face. Neither leaves a visible mark on the outside bead, which is why cutting a sample is the only reliable check.

How long before backfill?

Once the joint is below 40 °C, practically the full cooling time plus a handling allowance. Backfilling a warm joint with cold wet soil induces thermal shock.

Machines That Hold The Numbers

Butt fusion machines with the three-pressure schedule, calibrated gauges and the bead chart on the panel, from dn63 to dn1200. Tell us the diameter range and the joint volume and we will quote the right class.

Zhejiang Qingfa Pipe Technology Co., Ltd. · www.qingfaindustry.com · +86 151 6813 1515

Send Inquiry