Container Loading Calculator for HDPE Fittings
Nov 11, 2026
Leave a message
A fitting order that looks fine on a quotation can still lose money in the container. A 40HQ holds 76 cubic metres and about 26 tonnes, and those two limits are reached at completely different carton sizes: fill it with small couplings and the box runs out of space at 15 tonnes; fill it with DN400 elbows and it is over the payload while a third of the volume is still empty. The freight rate is the same either way.
The calculator below takes one carton and returns the three numbers a loading plan actually needs - cartons per container, pieces, and gross weight - together with the one number almost nobody checks before booking: which limit stopped the count.
Cartons per container
Measure one packed carton, not the product. Round nothing up.
The allowance field is the part most calculators leave out. A geometric fit assumes cartons slide past the door frame, stack to the roof with no dunnage and no pallets, and that every carton is exactly the stated size. Corrugated boxes swell by a few millimetres, straps add more, and a loading gang will not build a jigsaw to save two cartons. Ten per cent is a realistic default; drop it to five if you load on pallets that were already counted, raise it to fifteen for a mixed order with several carton sizes.
Which limit binds depends on the carton, not on the product
Volume and payload are reached at one specific carton density, and it is easy to compute. A 40HQ carries 26,500 kg into 76.3 cubic metres, so it reaches its payload only if the cargo averages 347 kg per cubic metre. A 20GP is far tighter: 28,200 kg into 33.2 cubic metres needs 849 kg per cubic metre, which almost no carton of plastic goods reaches. That is why a 20GP is described as a heavy container and a 40HQ as a light one, and why the same order can need two 20GPs where one 40HQ would have done.
Read the chart with a real carton in hand. A carton of DN32 electrofusion couplings at 150 kg per cubic metre never gets near either payload; you will be buying empty cubic metres and the only way to cut freight per piece is to make the carton denser. A carton of DN315 butt fusion elbows at 550 kg per cubic metre fills a 40HQ long before the volume is used, so the constraint is weight and the answer is to book by tonne rather than by cubic metre. The two cartons sit on the same price list and behave like different businesses.
Why the geometric maximum is not the number you load
The calculator counts cartons by testing all six orientations of the box against the internal dimensions of the container and keeping the best result. That is the correct way to do it - a single length-by-width-by-height division overstates the count whenever the carton does not divide evenly into the container's height, and the error is often ten per cent. What the count still cannot see is everything that happens on the floor of the container:
- Door height. A 40HQ has a taller box than a 40GP, but the door opening is smaller than the internal height. Cartons that stack to the roof inside will not pass the header if the last row is built outside and pushed in.
- The last row. Loading usually stops when the remaining gap is smaller than a carton, not when the container is full. On a 12-metre box a 32 mm gap sounds trivial, but the 248 mm of dead space above a 2,450 mm stack is a tenth of the volume.
- Pallets. A EUR pallet is 1,200 by 800 mm and 144 mm high, and it survives the journey as a stack of air. Palletising a 40HQ typically costs 10 to 15 per cent of the carton count.
- Mixed SKUs. Two carton sizes do not tile as well as one. Plan the heavy SKUs at the door end and accept that the count will be below the single-SKU figure.
Container reference figures
The tool uses the internal dimensions and payloads below. They are typical rather than exact - a container is a steel box that has been loaded a few hundred times, and the plate on the door is the figure that matters for a specific booking.
| Type | Internal L x W x H (mm) | Volume | Payload | Breakeven density |
|---|---|---|---|---|
| 20GP | 5,898 x 2,352 x 2,393 | 33.2 m³ | 28,200 kg | 849 kg/m³ |
| 40GP | 12,032 x 2,352 x 2,393 | 67.7 m³ | 26,700 kg | 394 kg/m³ |
| 40HQ | 12,032 x 2,352 x 2,698 | 76.3 m³ | 26,500 kg | 347 kg/m³ |
| 45HQ | 13,556 x 2,352 x 2,698 | 85.7 m³ | 27,700 kg | 323 kg/m³ |
Two practical notes on the table. A 45HQ is not accepted in every port and on every rail leg, and some trucking configurations will not take it, so the extra 9 cubic metres can strand an order. And the payload is the container's limit, not necessarily yours: road weight limits in the destination country, and the axle load of the truck collecting the box, often bite first.
A worked example with the numbers above
Take a 40HQ of DN110 SDR11 electrofusion couplings, packed 40 pieces to a carton of 600 x 400 x 350 mm at 24 kg gross. The best orientation gives 720 cartons as a geometric maximum. With a 10 per cent allowance the plan is 648 cartons, which is 25,920 pieces and 15,552 kg - and there the interesting part starts: the container is only 71 per cent full by weight, so nine tonnes of payload are being shipped empty.
The volume does not rescue it. 648 cartons occupy 54.4 of the 76.3 cubic metres, because the cartons cannot tile the container exactly; the missing quarter is the space above the stack and the gap at the door. Totalling those two numbers is the point of the tool: this order is limited by geometry, and no amount of clever loading turns it into a weight-limited one. If freight is quoted per cubic metre, a denser carton - fewer, larger pieces per box - is worth more than a cheaper unit price.
Now change one field. The same coupling in a carton of 400 x 400 x 300 mm at 30 kg, which is what a heavier pack looks like, still fits the same container by volume, but the payload count becomes 883 cartons against a volume count of 1,134. Weight binds, and the loading plan has to be built around tonnes.
What the calculator cannot tell you
Three things decide whether a container loads as planned, and none of them is arithmetic. The first is the actual carton, which is never the nominal size once it has been filled, taped and strapped. The second is the loading gang, whose stow is a judgement call about speed and damage rather than an optimisation. The third is the cargo itself: a 12-metre stack of cartons weighs on the bottom row, and fittings packed with heavy steel backing rings crush the layer below unless the cartons are specified for compression.
So treat the output as a planning figure with an allowance, then confirm with the forwarder on the day. For the specification side of the order - wall thickness, SDR and pressure class per size - use the fitting specification tables; for how the pieces are joined on site, see electrofusion fittings and the butt fusion parameter tables. If the order is going outside the EU, the HS code page covers the classification line that belongs on the same invoice.
Send Inquiry














