90 Degree Electrofusion Elbow | PE100, dn25 to dn900

90 Degree Electrofusion Elbow | PE100, dn25 to dn900

90 degree HDPE electrofusion elbow in PE100, dn25 to dn900, SDR11 and SDR17. Dimension tables for D, L1 and L, plus right-angle installation detail.
Send Inquiry

90 Degree HDPE Electrofusion Elbow (PE100) - Gas and Water Mains

A right angle is the hardest turn a buried gas or water main is ever asked to make. The whole change of direction is taken by one body, which then carries the full bending moment, sits under the same soil and traffic load as the pipe either side of it, and has to hold that for the life of the network. We make this 90 degree electrofusion elbow in PE100 across dn25 to dn900, for natural gas distribution, potable water and industrial process lines. The page carries the dimension tables size by size, the thrust figure that decides whether the corner needs anchoring, and the installation sequence that keeps a right-angle fusion sound.

  • Right angle in PE100, dn25 – dn900
  • Natural gas, LPG and water service
  • SDR11 to dn630, SDR17 to dn900
  • Made at our own works in Yuyao

How a Right-Angle Electrofusion Joint Is Formed

Each leg of the bend is a moulded socket with a copper coil wound into the wall. The pipe end is inserted, the welding machine reads the barcode on the fitting and applies the programmed voltage, and the coil melts the socket and the pipe wall together. There is no gasket and no insert: after cooling, the bend and the two pipe ends are one continuous piece of PE100.

A right angle puts one extra demand on the operator that a straight fitting does not. Both sockets are on the same rigid body at 90° to each other, so the pipe has to be square to each socket before either cycle starts. Push a leg in at an angle and it will still fuse - and the bend will sit a few degrees out, which on a right angle means it will not bed flat at both ends of the trench. That is why the installation sequence below puts dry-fitting and marking ahead of everything else.

For gas work the joint is the whole argument. Nothing in the assembly relies on an elastomer, so a gas distribution main carries no seal that can harden, shrink or weep over its service life - after fusion the socket and the pipe wall are a single continuous material. The same PE100 body is supplied to natural gas mains to the ISO 4437, EN 1555 and GB 15558 series and to potable water under WRAS approval, so one 90 degree elbow serves the gas main and the water main on the same job. We make the fitting at our own works, which is why a non-standard size or a project schedule can be discussed straight with the people who mould it.

The angle comes from the fitting, not from the joint. Once a leg is fused there is no mechanical way to rotate it - electrofusion makes the socket and the pipe wall one material. Correction means re-cutting the pipe run, not adjusting the bend.

Technical Specifications

Set out below as a parameter matrix rather than a list: each pair is a property and its value, read left to right, and the two pairs on any row belong to the same part of the argument - what the fitting is, what it is made of, and what it has to withstand once it is in the ground.

Part 90° equal elbow, moulded or machined to order Bend The two legs leave the body at 90°
Body PE100 polyethylene, 100% virgin resin, no regrind Size span dn25 – dn900
Pressure PN16 (SDR11) · PN10 (SDR17) Specified to Water: ISO 4427-3 · EN 12201-3:2024
Gas: ISO 4437-3 · EN 1555-3:2021 · GB 15558.2
Jointing Electrofusion - barcode weld cycle, any compatible EF machine Thrust About 1.41 × internal pressure × area on a right-angle turn
Anchoring Thrust block on undisturbed ground wherever the soil will not take the load Media Fuel gas and process gas; potable water and industrial water
Finish Black with UV stabiliser; yellow gas-grade marking on request Approvals ECM DN20–DN400 · ECM attestation DN20–DN1200 outside the EU · WRAS on moulded sizes
Branding Private label - mould number, logo and colour to your instruction Life Rated for 50 years or more in service

Sizes We Hold and Machine to Order

The 90° bend is the wider of the two angles. It reaches dn630 in SDR11 and dn900 in SDR17, and it is the angle that stays available above dn400 where the 45° in SDR11 has already stopped.

On gas networks this elbow tends to be ordered in two very different bands. Small sizes, dn25 to dn110, go into service connections, meter boxes and risers where the pipe has to turn square inside a short excavation; the large diameter sizes, dn315 to dn900, go onto distribution and transmission mains turning at road junctions, where a right angle is bedded and anchored as a thrust point. The machined sizes above dn500 carry a longer lead time than the moulded range because they are turned to order rather than shot from a cavity.

Buyers in Australia and New Zealand know the same component as a poly pipe elbow, and it is the same PE100 body, the same coil and the same fusion cycle - what differs between markets is the standard printed on the paperwork, not the fitting.

Range Series Production route
dn25 – dn500 SDR11 Injection moulded, standard production range
dn560 – dn630 SDR11 CNC machined to order from solid PE100
dn110 – dn500 SDR17 Injection moulded, standard production range
dn560 – dn900 SDR17 CNC machined to order from solid PE100

Machined sizes are quoted per order and carry a wider tolerance band, which is recorded size by size in the tables below. Socket geometry, coil pattern and barcode fusion cycle are the same as the moulded range, so a dn710 elbow fuses with the same machine programme as a dn63.

How the Right Angle Is Dimensioned: Ø D, L1 and L

Three numbers define the bend, and two of them mean something different from the same letters on a straight fitting. Getting them right is what stops a bend arriving that fits the pipe but not the trench.

Section drawing of a 90 degree electrofusion elbow showing dn nominal diameter, D outside diameter, L1 leg length and L centre to end face

Dimensioned section through the 90° elbow: dn nominal diameter, D outside diameter of the body, L1 leg length at each end, L centre-to-end length.

  • Ø D - outside diameter of the bend body, in mm. This is the body the trench has to accommodate, and it is larger than the pipe it joins.
  • L1 - leg length, the straight length of each socket leg measured from the end face. This is not the insertion depth of the pipe. It is what your clamping tool grips, and it is the length that has to sit on a sand bed rather than on the trench floor.
  • L - centre to end face: from the intersection of the two leg centrelines to the end of either leg. On a 90° bend both legs share this figure.

Why L matters more than it looks. L fixes where the two fusion joints land in the trench. On a dn315 90° bend, L is 278 mm, so the two joints sit 278 mm from the corner on each leg. If a chamber wall, a valve or a branch tee is dimensioned from the corner, that figure is what you subtract. It is also the number that tells you whether two bends can be stacked in a narrow excavation.

SDR11 dimensions - 90 degree elbow (PN16)

SDR11 series - 90° electrofusion elbow, dn25 to dn630
Nominal size Ø D (mm)
outside diameter of the body
L1 (mm)
leg length, each end
L (mm)
centre to end face
dn25 40±2 42±2 55±3
dn32 46±2 44±2 60±3
dn40 56±2 45±2 70±3
dn50 65±2 50±2 77±3
dn63 80±2 53±2 86±3
dn75 95±2 60±3 100±4
dn90 112±2 63±3 110±4
dn110 135±2 73±3 130±4
dn125 153±2 74±3 138±4
dn160 194±2 85±3 168±4
dn200 241±2 98±3 200±5
dn225 272±2 105±3 218±5
dn250 301±2 110±3 238±5
dn315 380±3 118±3 278±5
dn355 428±5 145±4 320±6
dn400 480±5 158±6 365±8
dn450 544±5 160±8 386±8
dn500 602±6 185±10 435±10
dn630 756±6 195±10 515±10

SDR17 dimensions - 90 degree elbow (PN10)

SDR17 series - 90° electrofusion elbow, dn110 to dn900
Nominal size Ø D (mm)
outside diameter of the body
L1 (mm)
leg length, each end
L (mm)
centre to end face
dn110 130±2 53±3 110±4
dn160 186±2 68±3 150±4
dn200 230±2 80±3 183±4
dn225 260±3 88±4 204±5
dn250 288±3 95±5 225±5
dn315 360±3 115±6 275±6
dn400 460±5 195±8 405±8
dn450 510±5 205±10 440±10
dn500 570±6 205±10 455±10
dn560 640±6 210±10 490±10
dn630 715±6 195±10 515±10
dn710 825±6 235±10 590±10
dn800 925±8 260±10 670±10
dn900 1025±8 275±10 715±10

Tolerances are moulding tolerances on the finished part. The wider bands on the larger sizes are the machined range - see the range page for why those sizes are turned rather than moulded.

Design Features

  • Full 90° range in one part number. dn25 to dn900, with SDR11 and SDR17 dimensions tabulated separately so the wall series can be matched to the pipe on site.
  • Coil and socket identical to the straight fittings. Same coil pattern, same barcode, same welding machine programme - no separate setup for bends.
  • Thicker fusion zone. The socket wall at each leg is heavier than the pipe wall, so the joint is not the weak point of the turn.
  • Smooth internal bore. No step at the bend, so flow passes the corner without an obstruction and nothing collects in the fitting.
  • Dimensioned for the trench. Ø D, L1 and L are published for every size, which is what allows the excavation and the clamp positions to be set before delivery.
  • Machined sizes on request. Above dn500 the bend is turned from solid PE100 to order, with the same socket geometry as the moulded range.
  • One body for gas and water service. The same PE100 mould is supplied to natural gas mains and to potable water lines, so a project that runs both can standardise on one 90° elbow - only the marking and the paperwork change.
  • Straight from the manufacturer. No trading supplier sits between the works and your order, so a bend can be quoted, scheduled and packed to the project rather than to a warehouse stock list, and a non-standard size can be discussed with the people who mould it.

Where a Right Angle Is Used

Gas and industrial gas networks

  • Service lines negotiating cellar walls and building entries
  • Distribution mains turning at road junctions and property boundaries
  • Regulator, meter and valve chambers, where the pipe has to leave vertically inside a short excavation
  • Industrial gas headers routed around structural steel

Water and process lines

  • Rising mains where the pipe turns from horizontal to vertical at the base of a riser
  • Water mains turning at road junctions and property boundaries
  • Factory cooling and process water circuits routed around equipment
  • Repair sections, where a right angle restores a route without a fabricated bend

Fitting a Right Angle in the Trench

What a right angle does to the pipe

The pipe is strong in tension along its axis and comparatively weak against bending, and a 90° turn is where bending is concentrated. Three loads arrive at the same point:

  • Internal pressure acting on the turn. A pressurised bend produces a resultant thrust that tries to straighten it out. The thrust grows with bore and with pressure, which is why a dn25 bend needs nothing and a dn500 bend needs anchoring.
  • Soil and traffic load from above. The outside of the curve is where the wall is thinnest relative to the radius, so it is the first place to deform under a settlement load.
  • Thermal movement along both legs. A buried PE main expands and contracts with ground temperature, and at a corner those movements push against each other instead of running past.

The bend itself is designed for all three - the fusion zone at each socket is thicker than the pipe wall, and the bore is smooth through the turn, so there is no step for the flow to work against. But the bend can only do that if the ground around it does its job, which is the part of the installation that is usually done badly.

Fusing a right-angle joint

The order of work matters on a bend in a way it does not on a straight run:

  1. Dry-fit and mark first. A right angle that is fused a few degrees out cannot be corrected afterwards. Assemble the bend between the two pipe ends with the clamps loose, confirm the corner square against your reference, and mark both pipe ends before any current is applied.
  2. Support the legs, not the corner. The bend should sit on a sand bed along both legs. Supporting it under the curve leaves the sockets hanging and puts the joint under load during fusion.
  3. Fuse one leg, let it cool, then the other. Running both cycles back to back while the first socket is still hot stacks the residual stress from both joints into the corner. Cool the first joint to the machine's specified time before starting the second.
  4. Do not disturb the joint to check it. The witness bead on the inspection port is the check. Twisting a hot joint to confirm alignment is how a good fusion becomes a leak.
  5. Backfill in layers. Sand or fine fill to at least 150 mm over the bend, compacted either side rather than directly on top of the curve, before the general backfill goes in.

Where a thrust block is needed. On a pressurised main in ground that will not hold the fitting - soft clay, peat, loose fill - a right angle is normally anchored with a concrete block bearing on undisturbed ground behind the corner. Whether that is required is set by your pipeline design, not by the fitting. Tell us the application at enquiry stage and we will confirm the fitting that suits it.

FAQ

How much thrust does a 90° bend generate?

The resultant thrust on a pressurised 90° turn is roughly 1.41 times the product of internal pressure and cross-sectional area. That is why anchoring requirements climb steeply with bore: doubling the diameter quadruples the thrust. Your pipeline design fixes the anchor detail; the bend is rated for the pressure of its wall series.

Does a right-angle bend always need a concrete thrust block?

No. Many small-diameter service connections need nothing beyond correct compaction. The block becomes necessary where the soil will not carry the thrust - soft or saturated ground, or large bore on a pressurised main. This is a design decision, and we will ask about it at enquiry stage rather than assume.

Can the angle be corrected after fusion?

No. Electrofusion joins the socket and the pipe wall into one continuous material. Once a leg is fused there is no mechanical way to rotate it. Any correction has to come from re-cutting the pipe run, not from the fitting.

What do L1 and L mean on the table above?

L1 is the leg length - the straight part of each socket leg, which is what clamps grip and what has to sit on a sand bed. L is the centre-to-end length, from the crossing point of the two leg centrelines to the end face. Neither is the pipe insertion depth.

Can SDR11 and SDR17 bends be joined to each other?

They can be physically fused, but doing so puts a lower-rated joint into a higher-rated line. Match the bend to the pipe series: SDR11 to SDR11, SDR17 to SDR17.

Do you supply the welding machine programme for these sizes?

The fusion cycle is carried on the fitting barcode for all moulded and machined sizes. Machine barcode readers and the standard fusion machines used across our range read it directly.

Is the 90 degree elbow approved for natural gas service?

It is, and on this angle the paperwork is what decides the answer rather than the material. Natural gas distribution is covered by ECM type approval from DN20 to DN400, which names elbows explicitly; above dn400 the range continues under an ECM attestation issued for third countries outside the EU, the usual route for the Middle East, South-East Asia and Africa. The body is PE100 throughout and the fusion leaves no elastomer in the gas path, so nothing inside the main can perish over its 50-year design life. GB 15558 is added to the documents for Chinese networks and gas-grade yellow marking is available on request. Send us the standard your network is designed to and we will confirm which document applies to the sizes on your order.

How is the 90 degree elbow priced, and is there a minimum order?

There is no published list price, because the figure moves with the size, the wall series and whether the bend is shot from a mould or turned from solid. Give us the sizes and we will quote your order rather than a catalogue. We sell direct from the works, so no stockist margin sits between the fitting and your project, and an order of one piece for a repair is handled the same way as a container load - the process does not change with the volume. Send the quantity, the standard you are working to and the destination port, and the reply carries the price, the lead time and how it will be packed.

Certification Documents

On a 90° bend the two things that matter are how far the documentation reaches and which market it is valid in, because this angle spans dn25 to dn900 while the certificate range stops at dn400. Both are set out below, taken from the documents themselves.

Document Holder What it covers Valid to
ECM Type Approval
certificate 1N240805.PTSQC86
PTS Tech Solutions Sdn Bhd, Malaysia HDPE electrofusion and butt fusion fittings, DN20 – DN400, including elbows. Standards BS EN 1555-3:2021, BS EN 12201-3/-4:2024. 04 Aug 2029
ECM Attestation
1N241120.ZQPSW72
Zhejiang Qingfa Pipe Technology Co., Ltd. PE pipe fittings DN20 – DN1200. Issued under a non-notified procedure and expressly for markets outside the EU. 19 Nov 2029
WRAS material approval
251155041
Zhejiang Qingfa Pipe Technology Co., Ltd. PE100 black injection moulded fittings for contact with wholesome water, up to 65 °C. Machined sizes fall outside this scope. Nov 2030
CNAS-accredited test data Own test laboratory Coil resistance, fusion joint strength and dimensional checks, reported per batch on request. per batch
ECM type approval certificate 1N240805.PTSQC86 for HDPE electrofusion and butt fusion fittings DN20 to DN400, with elbows named on the certificate
ECM certificate
DN20–DN400
ECM type approval attestation 1N241120.ZQPSW72 held by Zhejiang Qingfa, covering PE pipe fittings DN20 to DN1200 for markets outside the EU
ECM attestation
DN20–DN1200
CNAS laboratory accreditation to ISO/IEC 17025:2017 for the Qingfa testing centre
CNAS
ISO/IEC 17025
WRAS material approval 251155041 for PE100 black injection moulded fittings for wholesome water
WRAS
251155041
GB/T 27922-2011 five-star after-sales service certificate for HDPE pipe fittings
GB/T 27922
after-sales

Note on the size ceiling at this angle. The ECM certificate reaches dn400. The 90° range continues to dn900 under an ECM attestation, a non-notified document valid only for consignments bound for non-EU markets - the normal route for the Middle East, South-East Asia, Africa and Latin America. For a dn450+ elbow going into a project inside the EU, tell us at enquiry stage so the documentation is settled before you specify. WRAS covers the injection moulded range only, so a machined dn630 or dn900 bend is not covered by it.

Where These Bends Are Made

Our 90° bends are moulded and machined at the same works in Hemudu Town, Yuyao, Zhejiang that runs the electrofusion couplers and tees - which is why we quote as the manufacturer rather than through a trading layer. Moulded sizes come off the presses used for the straight fittings; machined sizes are turned from solid PE100 on CNC centres and then gauged individually, which is why the tolerance band on those sizes is wider, and why the lead time on them is longer.

On a right angle the two numbers that decide whether the fitting fits the trench are the angle itself and the centre-to-end length L. Both are measured on the finished part, after cooling. Every batch carries a traceable production record - resin batch, machine, operator shift and fusion test result - released with the shipping documents on request.

Injection moulding machine producing large diameter 90 degree electrofusion elbow bodies at Qingfa

The presses that make the large-bore 90° bodies

Injection moulding workshop at Qingfa running PE100 electrofusion fitting moulds

The moulding hall

CNC turning workshop where machined dn560 to dn900 electrofusion elbows are finished at Qingfa

CNC turning - where the machined dn560 – dn900 bends are cut and gauged

Packing, Marking and Shipping

A right angle is the least stackable shape we make. The end faces cannot take the load and the outside of the curve is where the wall is thinnest, so packing is built around the corner.

  • One layer per crate from dn315 upward, with the curve supported and the legs bedded.
  • Socket bores capped and the crate ends lined, so the coil terminals and sealing surfaces arrive unmarked.
  • Angles kept separate in the crate plan - each 90° item is placed so its corner is not bearing on another fitting.
  • Every bend marked on the body - nominal size, the 90° angle, wall series and the fusion barcode go onto the part itself, so identification never depends on the label or the crate.
  • Shipping paperwork complete - invoice, packing list, certificate of origin and the batch fusion reports travel with the consignment rather than following it.
90 degree HDPE electrofusion elbows and fittings packed and staged in the Qingfa warehouse

Fittings staged for dispatch - the corner sits up, never load-bearing

Cargo leaves via Ningbo, consigned to utilities, pipeline contractors and distributors across the Middle East, South-East Asia, Africa, Australia and Latin America. A right-angle body is awkward to pack, so if you want to see how your sizes are crated, ask at enquiry stage and we will photograph the load before the container doors are shut.

Send the pipe size, wall series (SDR11 or SDR17), the design pressure and the required L dimension through the enquiry form and we will confirm the bend, the price, the lead time and the packing. If the route is already fixed, a marked-up drawing is the fastest way to quote it right first time.

Turning through a low-loss angle instead? See the 45 degree electrofusion elbow, and the comparison of two 45s against one 90. Where the run is straight rather than turned, the matching component is the HDPE electrofusion coupling.

Looking for a dependable supplier of 90 Degree Electrofusion Elbow? Qingfa Industry has been manufacturing PE100 pipe fittings since 1999, in its own moulds in Yuyao, Ningbo. See how our PE fittings are made.

Hot Tags: 90 Degree Electrofusion Elbow | PE100, dn25 to dn900, 90 Degree Electrofusion Elbow | PE100, dn25 to dn900 SDR11/SDR17, PE100 90 degree electrofusion elbow | pe100, dn25 to dn900, 90 degree electrofusion elbow | pe100, dn25 to dn900 supplier, HDPE End Cap, End Cap HDPE Pipe, End Cap HDPE, PE PiPE End Cap, Electrofusion Test Cap, HDPE PiPE End Cap

Send Inquiry