How To Calculate Butt Fusion Pressure, And Why No Pressure Table Exists

Nov 03, 2026

Leave a message

Butt Fusion · Pressure
How To Calculate Butt Fusion Pressure, And Why No Pressure Table Exists

Every week someone asks us: what pressure for 300 mm PE pipe? There is no fixed answer, and any supplier who hands you a one-page pressure table is guessing.

Total fusion pressure depends on three things that change per job: pipe wall area, your machine's cylinder area, and the drag pressure you measure on site. The time values that go with it are in butt fusion welding parameters.

0.15 MPa
Reference interfacial stress
0.91 MPa
dn315 SDR11, 90 mm bore
0.05-0.1 MPa
Margin to add, not 0.5-1
Formula

The Formula In Three Lines

Calculation

Total pressure = drag pressure + interfacial pressure. Interfacial pressure = 0.15 MPa x (pipe annular area / cylinder effective area). Pipe annular area = 0.7854 x (OD squared - ID squared).

  • 0.15 MPa is the reference interfacial pressure for PE100 at standard ambient. It is a target stress at the joint face, not a gauge reading.
  • Cylinder effective area comes from the bore and rod diameter. It is in the manual and it is fixed for a given machine.
  • Drag pressure is friction: pipe weight, roller condition, alignment, insert condition.
Step 1

Measure Drag Pressure, Do Not Assume It

With the pipe clamped and aligned but the heater out, bring the carriage together slowly and read the gauge at the moment the pipe ends just touch and start to move.

  • New machine, clean rails, short dn160 pipe: typically 0.1-0.2 MPa
  • Long dn315 string, worn rollers, dirt on the rails: 0.3-0.5 MPa
  • Above 0.6 MPa: stop and fix the machine. That much friction means the pressure you apply is not reaching the interface, and the joint will be under-fused whatever you set.
Step 2

Calculate: dn315 SDR11 Worked Example

Worked example: dn315 SDR11, PE100, machine with a 90 mm bore cylinder, effective area 6362 mm².

  • OD = 315 mm, e = 28.6 mm, so ID = 257.8 mm
  • Annular area = 0.7854 x (315 squared - 257.8 squared) = 0.7854 x 32,764, about 25,730 mm²
  • Interfacial pressure = 0.15 x 25,730 / 6,362, about 0.607 MPa
  • Measured drag = 0.30 MPa
  • Total to set = 0.91 MPa

Set 0.9 MPa, and check the bead at bead-up: if the collar forms noticeably faster than the target height suggests, the drag reading was low.

Step 3

Apply The Margin Correctly

Hose loss, gauge error and drag variation all push the delivered pressure below the calculated value. Add 0.05-0.1 MPa, which is 0.5-1 bar, not 0.5-1 MPa.

A ten-fold error here is a real failure mode: 1 MPa extra on a dn160 joint squeezes most of the melt out of the interface and thins the wall at exactly the point that has to hold pressure. Boxed gauges are a common cause, and the symptom is a joint that looks over-formed but opens on the cut face.

Variables

Why The Number Changes For The Same Pipe

Variable Effect on required gauge pressure
Pipe string weight and support Higher drag, higher total
Roller and rail condition 0.1-0.3 MPa spread between maintained and neglected machines
Cylinder bore Smaller bore needs higher gauge pressure for the same face stress
Wall thickness at the same OD SDR17 dn315 needs roughly 60 % of the interfacial pressure of SDR11
Ambient temperature Minor direct effect, large indirect effect through drag and melt behaviour

The same logic explains why two crews with identical machines and identical pipe produce different joints: one of them measured drag on the day. Wall ratio selection itself is covered in SDR11, SDR17 and SDR21 compared.

Errors

Three Errors We See Most

  • Using drag pressure as the welding pressure. Drag alone produces no interfacial stress: the joint is formed by pressure above drag.
  • Setting the same gauge value across SDRs. A crew that welds SDR11 all week and then gets an SDR17 string keeps the number and over-pressures every joint.
  • Not re-measuring drag after a pipe change. Drag is a property of the setup, and the setup changes when the pipe does.

All three produce the same end state: a joint that passes a pressure test today and separates at the interface a season later. The inspection that catches it before backfill is described in cold fusion and false fusion.

FAQ

Frequently Asked Questions

What pressure should I use for 315 mm PE pipe?

There is no single number. For SDR11 PE100 on a 90 mm bore machine with 0.30 MPa measured drag it is about 0.9 MPa; for SDR17 on the same machine it drops to roughly 0.65 MPa.

What is drag pressure?

The pressure needed to overcome friction and move the pipe string, measured with the ends just touching, before any fusion pressure is applied.

Can I read fusion pressure from the bead?

Partly. A bead that forms too fast or too large indicates over-pressure, a small slow bead indicates under-pressure. It confirms the calculation, it does not replace it.

Gauges And Machines You Can Trust The Number On

Calibrated pressure gauges, contact thermometers and hydraulic machines with a documented cylinder area, so the calculation above survives contact with the trench.

Zhejiang Qingfa Pipe Technology Co., Ltd. · www.qingfaindustry.com · +86 151 6813 1515

Send Inquiry